Photoshop one-Tone brown portrait Photo tutorial

For the users of Photoshop software, share one-tone brown portrait photo tutorial.

Tutorial Sharing:

Original

1, open the material picture, create an optional color adjustment layer, the cyan adjustment, parameters and effect of the following figure. This step turns the cyan in the picture into green.

< map 1>

< map 2>

2, create hue/saturation adjustment layer, yellow, green, green adjustment, parameter settings such as Figure 3-5, the effect is shown in Figure 6. This turns the background color into a neutral color.

< map 3>

< map 4>

< map 5>

< map 6>

3, press CTRL + J to copy the current hue/saturation adjustment layer, the effect of the following figure.

< map 7>

4, create curve adjustment layer, the RGB, red, blue channel adjustment, parameters and effect of the following figure. This step darkens the dark part of the picture and increases the reddish-brown tone.

< map 8>

< map 9>

5, create optional color adjustment layer, dialogue, neutral, black to adjust, parameter settings such as Figure 10-12, the effect is shown in Figure 13. This step adds a light cyan to the picture's high light portion, and the dark part increases the reddish-brown.

< map 10>

< map 11>

< map 12>

< map 13>

6, create a new layer, press the letter key "D" before the background color to restore to the default black and white, and then select the menu: Filter > Render > Cloud, after determining the blending mode to "filter Color", the opacity to: 30%, the effect of the following figure. This step adds a mask effect to the picture.

< map 14>

7, create curve adjustment layer, the RGB channel adjustment, a little bit dim, and then press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 16.

< map 15>

< map 16>

8, create a color balance adjustment layer, the shadow, highlight adjustment, parameter settings such as Figure 17,18, determine the above method to create a clipping mask, the effect is shown in Figure 19. These two steps fine-tune the shade and color of the cloud.

< map 17>

< map 18>

< map 19>

9, press CTRL + ALT + 2 to bring up the high light selection, press CTRL + Shift + I to select the dark selection, then create the curve adjustment layer, the RGB, red channel adjustment, parameters and effects as shown below. This step darkens the dark area of the picture.

< map 20>

< map 21>

10. Create a new layer, use the elliptical marquee tool to pull out the selection shown in the following figure, feather 65 pixels and fill the pale brown: #D7CBC0, remove the selection after the following figure.

< map 22>

11. Press CTRL + J to copy the current layer, press CTRL + T to shrink a little, and then create a clipping mask, then change the blending mode to "filter Color" and change the opacity to: 40%, the effect is as follows.

< map 23>

12, create a color balance adjustment layer, adjust the high light, parameter settings such as Figure 24, after the creation of a clipping mask, the effect is shown in Figure 25. These steps give the picture a high light rendering.

< map 24>

< map 25>

13, create curve adjustment layer, the RGB channel adjustment, parameter settings such as Figure 26, to determine the mask filled with black, and then use a white brush to the bottom and left part of the wipe out, the effect is as figure 27. This step adds a dark angle to the picture.

< map 26>

< map 27>

14. Create a new layer, press CTRL + ALT + Shift + E-stamp layer, and blur the next figure selection with the Blur tool.

< map 28>

15, a new layer, stamped layer, select menu: Filter > Blur > Dynamic blur, Angle set to 45 degrees, the distance is set to 150, to determine the blending mode to "soft light", the opacity to: 30%, the effect of the following figure. This step of the picture to soften processing.

< map 29>

16, using the Lasso tool to select the selection shown in the following figure, feather 65 pixels and press CTRL + J to copy to the new layer, the effect of the following figure.

< map 30>

17, the creation of optional color adjustment layer, red, white, black adjustment, parameter settings such as Figure 31-33, the effect is shown in Figure 34. This step appropriately reduces the red in the picture and adds a light cyan to the high light portion.

< map 31>

< map 32>

< map 33>

< map 34>

18, create curve adjustment layer, the RGB channel adjustment, parameter settings such as Figure 35, to determine the mask filled with black, with a white brush to wipe out the character backlight area, the effect is shown in Figure 36.

< map 35>

< map 36>

Finally fine-tune the color, give the picture to add some small point decoration, complete the final effect.

Okay, the above information is small to give you photoshop this software users of the detailed one-tone brown portrait photo tutorial to share all the content, you see the users of Photoshop software here, small knitting believe you are now very clear, Hope that the small part of the sharing can bring help to everyone.