Photoshop retains details to pull out portrait hair silk effect

Source: Internet
Author: User
Tags final

Original

Final effect

Change background effect

Enlarge Detail Diagram

1, open the material picture, enters the channel panel, first observes three channels, if 1-3, finds the hair and the background color difference ideal channel, here green channel is better.

2, the green channel to copy one, get green copy channel, the hair part slightly enlarge a point, the top area of the hair and background more close, more difficult to deal with, the following figure.

3, first to the overall brightness, press CTRL + L adjust the color, adjust the back of the high smooth block, the edge of the change to see the hair, the details began to lose when it is not adjusted, the following figure.

4, we only need to pull out the hair in the channel, first with a lasso to select the hair part, and then reverse the selection, the appropriate feather filled with white. The advantages of doing so are many, the hair part is relatively simple and many, not affected by the external environment.

5, the initial brightness of the hair after the light and dark part is very obvious. It is now processed from the bottom of the right to the beginning. First Use the Lasso tool selection in Figure 8, the selection, feather 10 pixels and press CTRL + L to brighten, as shown in Figure 9. The standard of dimming is not to lose details, when the details begin to be lost when the light is stopped, such as Figure 9 in the local and gray area.

6, cancel the selection, and then use the Lasso tool to select the parts that are not illuminated, feather 5 pixels and continue pressing CTRL + L to brighten, the effect is shown in Figure 11.

7. The first paragraph is basically finished, and the outer area of the hair is selected to fill with white with lasso.

8, then the above paragraph to deal with, continue to use the Lasso tool to select the part that needs to be highlighted, feather 3 pixels and press CTRL + L to brighten, as shown in Figure 14.

9, adjust the time does not necessarily have to turn gray all white, hair and gray between the white space can also be, so as to avoid the loss of details, the following figure.

10. Select the outer part of the hair with the lasso, fill the white, the second paragraph also completes smoothly.

11, the third paragraph is more difficult to deal with. First select this section with the Lasso tool, feather 3 pixels and press CTRL + L to brighten a bit with a color.

12, and then from the bottom of this section to the gray part of the selection, the appropriate feather after the light.

13, thin hair this piece is the same way to brighten up a bit first, and then adjust the local.

14, and then use the lasso to select a small range of details of the lighting, such as Figure 26,27.

15, after the light, with the Lasso tool to select the edge of the part, filled with white.

16, the fourth paragraph is relatively simple, direct selection of light.

17, the fifth paragraph is also relatively easy, first the overall brightness, and then the middle of the gap part of the light, as shown in Figure 32-35.

18, this is now seen the effect of the partial and defective can be dealt with again. The overall is better, the details remain very good.

19, press CTRL + I to reverse the current channel, and then press CTRL + L to lighten up a bit with a level of color.

20, hold down CTRL + the left mouse button click the green Copy channel thumbnail to load the selection.

21, point RGB Channel, return to the Layer panel, the following figure.

22, press CTRL + J to copy the selection part of the hair to the new layer, and then on the background layer to create a new layer fill pale green, the effect of the following figure.

23, press CTRL + J to copy the layer of hair layer, the opacity is changed to: 50%, the effect of the following figure.

24, with a pen to check out the main part of the characters, copied to the new layer, moved to the light green layer above, the effect of the following figure.

25, to this step only completed the half, the most critical part is to deal with the details. Copy the background layer one layer, press CTRL + Shift +] top. Then copy the background copy one more layer, so you get the background copy 2 layer. Back to the background copy 1 layer, hold down the ALT key to add the layer mask.

26, select the Brush tool, the size is 1 pixels, opacity is 10%, and then set the foreground color to white.

27, the background copy of the 2 layer display, in the background part of the 1 mask smear hair, you can enlarge the hair part of a point.

28, this is painted hair, although more trouble, but it is much easier than to draw a hair. After this step, the hair and details will not leak, very perfect. This is also my original method, very practical.

Finally change the background, you can deal with the details, complete the final effect.

Category:
    • PS Pull Map Tutorial

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.