Photoshop Synthetic Beauty Portrait abstract watercolor Decoration effect

This tutorial mainly uses Photoshop synthetic beauty portrait abstract watercolor decoration effect, the use of watercolor material and tree branches flower butterflies, through the mask board, Shearing mask, multiply, overlay, soft light, strong light and other tools to blend them together and to color to make the whole more artistic atmosphere.

First look at the effect chart:

1, first to make the background of the paper, a new 1200x800 document, drag into the material copy more than 2 layers out, deformation tools to adjust the position.

Then merge the 3 layer ctrl+e into one layer, set the opacity of the layer to 30%, drag into the pastel material, and then resize it to set its opacity to 30%.

Add an adjustable layer---hue/saturation, parameters like figure

Some people may ask why they make this color, well that's because the white canvas is made to look like a watercolor-colored paper that's been wet and dry.

2, drag into the beauty material, put in the middle of the adjustment good size, not too small also not too big. A big one will add other materials inconvenient, small made out of the work is too small and not good-looking.

And then pull out the beauty, how to pick a lot of casually here not limited. I used the RGB channel filter + inverse + selection subtraction + fill white bottom to pull out. After you pull it out, add the mask with the soft side brush (CS6 inside the 3rd brush, opacity 60%), and rub it into this effect

3, color palette add 3 adjustable layer is "hue/saturation", "Color balance", "curve", and then the parameters are as follows:

The effect is this after the adjustment.

But in this way the back of the paper are discolored, this is not the effect we want. So we're going to add these 3 adjustable layers to the clipping mask so that the 3 effects only work on the beauty layer rather than the entire screen, creating a clipping mask is simple:

Just hold down the ALT key to move to the color layer above the beauty layer of the place, there will be a white box with a downward arrow pointer on the right, click the left mouse button, it created a clipping mask. Add a clipping mask to all 3 layers, as shown in the figure:

4, in order to facilitate the management of these layers can now be grouped together. Now drag the Watercolor footage 1, adjust the opacity to 55% this is to make it easier to see the layers below so the adjustment position is not wrong

After adjusting the position, set the opacity back to 100%, mix the layer to "multiply", and then add the mask to erase the excess parts.

Then drag into the watercolor material 2 with the above method to adjust the position, the mixing effect is "multiply bottom"

As well as adding masks, erasing unwanted parts

Then drag it into the tree to adjust the position.

Add a mask, erase the superfluous parts, if encountered some branch angle is not very good, you can choose to adjust the box, alt+e Select "Control deformation", tools to modify

After deformation if there is a gap in the middle of the box can be selected with a gap in the part of the SHIFT+F5, the use of content recognition to intelligently fill the gap part. And then you can decorate it in the mask.

Then the CTRL+M curve tool modifies the brightness

Drag into the kidney fern material, adjust the position, multiply the bottom, erase the superfluous parts, and curve tool adjust dot brightness

5. Create a new blank layer, name the cloud filter, set the foreground color to #A8BA81 background color #012955, and then press the M box to select the tool and draw a selection. Press alt+t----"Render"---"Cloud"

Then continue to filter---pixel---mosaic

Remove a selection, filter---distort----polar coordinates

After the completion of the ctrl+t size, and then lower left corner, lower right corner of the two vertices, drag the mouse to the inside, so that he has a sense of perspective

Use the Pen tool to sketch out the extra parts and then move to a selection to feather 1.5 pixels.

Then the layer blending mode for the "strong light" observed that the color with the whole a little bit of a tune, you can use Ctrl+b color balance to adjust the color so that it with the main tone of the integration more appropriate

6. Create a new blank layer, name the lip, paint the lip with the pen, turn the path feather 1.5 pixels and fill the color #779370, then the layer blending mode is "strong light"

Classification:

• PS Composite Picture Tutorial