To give you Photoshop software users to detailed analysis to share a bright blue color to adjust the effect of the palette tutorial.
1, open the original material big picture, press CTRL + J to copy a layer of background layer, using fuzzy tools to the next figure selection part of the fuzzy processing, the effect of the following figure.
2, create a new layer, press CTRL + ALT + Shift + E-stamped layer, blending mode to "multiply", hold down the ALT key to add a layer mask, with less transparency soft edge white brush lower left corner area, the effect of the following figure.
3, press CTRL + J to copy the current layer layer, the opacity to: 30%, the effect of the following figure.
4, create curve adjustment layer, RGB, blue channel adjustment, parameter settings such as Figure 4, the effect is shown in Figure 5. This step is mainly to the image of the dark and high light area to increase the blue.
5, press CTRL + J the current curve adjustment layer copy one layer, the opacity to: 20%, the effect of the following figure.
6, create an optional color adjustment layer, the yellow, green adjustment, parameter settings such as Figure 7,8, the effect is shown in Figure 9. This step mainly turns the green in the picture into a lighter orange color.
7, create color balance adjustment layer, shadow, highlight adjustment, parameter settings such as Figure 10,11, the effect is shown in Figure 12. This step also adds blue to the dark and high light areas of the picture.
8, CTRL + ALT + 2 up the high light selection, and then create a curve adjustment layer, RGB, red, green, blue channel adjustment, parameter settings such as Figure 13-16, the effect is as Figure 17. This step lightens the highlight area of the picture and increases the light blue.
9, create a new layer, press the letter key "D" before the background color back to the default black and white, and then select the menu: Filter > Render > Cloud, determine the blending mode to "color". Hold down the ALT key to add a layer mask, and use a soft white brush with less transparency to paint the upper-right area of the picture.
10, press CTRL + J to copy the current layer layer, the effect of the following figure.
11, press CTRL + J to copy the current layer, mask filled with black, and then use the soft side of the white brush to the top of the upper right corner of the area, the effect of the following figure. These steps add smoke and light to the top right corner of the picture.
12, the background layer to copy a layer, press CTRL + Shift +] top, with the pen tool to pull out the characters, into the selection after adding layer mask, and then the layer opacity to: 50%.
13, create curve adjustment layer, the RGB, red, blue channel adjustment, parameter settings such as Figure 22, determined to press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 23. This step lightens the character part slightly and increases the blue color.
14, create hue/saturation adjustment layer, the appropriate reduction of the entire figure lightness, parameter settings such as Figure 24, determine after the creation of a clipping mask, and then the mask filled with black, and then with a lower transparency of the soft edge white brush the character backlight area, the effect is as shown in Figure 25.
15, press CTRL + J to copy the current hue/saturation adjustment layer, the same way to create a clipping mask, the effect of the following figure.
16, with their familiar method to the lower left corner of the picture to increase the dark angle, the following figure.
17, the creation of optional color adjustment layer, green, white adjustment, parameters and effects as shown below. This step adds a light blue to the picture.
18, create a solid color adjustment layer, the color is set to light cyan: #F8FFFF, after the mask filled with black, and then with a low transparency soft edge white brush to the upper right corner area, the effect of the following figure. This step adds a light cyan to the upper-right corner of the picture.
19. Create a new layer, use the elliptical marquee tool to pull out the oval selection shown in the following figure, feather 45 pixels, and then fill in the dark blue: #546898, remove the selection and change the blending mode to "color filter", the effect is as follows. This step adds a blue high light to the picture part.
Finally, fine-tune the color to complete the final effect.
Well, the above information is small compiled to you photoshop this software users brought to the details of the bright blue color portrait effect of the palette to analyze the full content of the share, you see the users here, small knitting believe that you are now very clear color method of the bar, In general, the background of the fuzzy processing, and then press the dark corners, and then use the palette to pull out the blue tone, and finally through a number of selections to the high light part of the rendering process can be, then you now go to try it.
