Photoshop to the street beauty plus dark Yellow

Material picture The sky part is a bit white, color matching time need to fill with gradient color, and then the background part of the main color into blue, high light part of the increase in orange yellow.

Original

　Final effect

1, open the material picture, create an optional color adjustment layer, the yellow adjustment, parameters and effect of the following figure. This step turns the yellow in the picture into green.

< map 1>

< map 2>

2, create an optional color adjustment layer, green, cyan adjustment, parameters and effect of the following figure. This step turns the turquoise green in the picture into blue.

< map 3>

< map 4>

< map 5>

3, press CTRL + J to copy the current optional color adjustment layer, the effect of the following figure.

< map 6>

4, create curve adjustment layer, RGB, red, green, blue channel adjustment, parameter settings such as Figure 7-10, the effect is shown in Figure 11. This step deepens the darker color of the picture and adds light yellow to the high light portion.

< map 7>

< map 8>

< map 9>

< map 10>

< map 11>

5, create a new layer, select the gradient tool, color settings such as Figure 12, and then pull down the top of the linear gradient. When you are sure to add a layer mask, rub the bottom transition with a black brush, as shown in Figure 13.

< map 12>

< map 13>

6, the background layer to copy a layer, press CTRL + Shift +] Top, hold down the ALT key to add a layer mask, with a white brush to wipe out the characters, the following figure.

< map 14>

7, create curve adjustment layer, the RGB, red, blue channel adjustment, parameter settings such as Figure 15, determined to press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 16. This step darkens the character part slightly, and the high light part increases the light yellow.

< map 15>

< map 16>

8, with a pen to check out the hair by the light area, feather 6 pixels after filling orange yellow: #FFD996, after the blending mode is changed to "strong light", the opacity to: 50%, and then the same method to create a clipping mask, the effect of the following figure.

< map 17>

9, with a pen to check out the edge of the selection of high light, feather 2 pixels after filling the same as the orange color, mixed mode to "soft light", the same method to create a clipping mask, the effect of the following figure.

< map 18>

10, create curve adjustment layer, RGB, red, blue channel adjustment, parameter settings such as Figure 19-21, the effect is shown in Figure 22. This step deepens the darker part of the picture, adding orange and yellow to the entire image.

< map 19>

< map 20>

< map 21>

< map 22>

11, create a solid color adjustment layer, color set to dark green: #47634A, after the mask filled with black, with a lower transparency white brush to wipe out the bottom area, and then change the layer opacity to: 50%, the effect of the following figure. This step darkens the bottom of the picture a little bit.

< map 23>

12, create a new layer, press CTRL + ALT + Shift + E-stamped layer, select menu: Filter > Blur > Motion blur, Angle set to 40 degrees, distance set to 160, after the blending mode to "soft light", the opacity to: 30%, the following figure.

< map 24>

13, a new layer, stamped layer. With the fuzzy tool to the next figure selection part of the pattern processing, while the picture can be added a little light red, the effect of the following figure.

< map 25>

14, create curve adjustment layer, the RGB channel adjustment, the dark part of the black, to determine after the mask filled with white, with a brush to wipe out the corners, the effect is shown in Figure 27. This step adds a dark angle to the picture.

< map 26>

< map 27>

15, the local according to need to add a little high light, the effect of the following figure.

< map 28>

Finally, simply rub the skin of the character, fine-tune the overall color, complete the final effect.

Category:

• PS Palette Tutorial