Precautions for configuring IPv6 in Windows 7

IPv6 has quietly come to our side. Windows 7 has started to support IPv6, but

For the user, Windows 7 has not been figured out yet, and now it is very difficult to add an IPv6

Dizzy users cannot even touch their minds. The following describes how to configure

IPv6.

I. Initial problems:

Some schools will update their internal network addresses

IPv6, so it is often necessary to determine the IPv6 address to visit the site. But recently I have noticed that

Some internal school sites that can log on normally receive an error message indicating that they cannot be accessed.

These sites are equipped with IPv6 addresses.

Ii. Think about troubleshooting:

Your own machine is a t400 notebook, and the device is a genuine Windows 7 Ultimate Operating System.

To better locate the source of the fault, and to discuss other machines, especially the machines with the XP System

I have no questions about the above websites. It seems that the fault is caused by the configuration of Windows 7.

.

(1) Configure IPv6 parameters from the menu:

Next, we will discuss how to find and handle network search. We will first start with IPv6 Configuration. The detailed steps are as follows:

.

Step 1: Right-click the "network" icon on the desktop and select Properties to enter the network sharing center.

Click to enter the local connection.

Step 2: configure the Local Connection Properties and find Internet Protocol version 6.

(TCP/IPv6) option, double-click to open a new window to execute the configuration.

Step 3: Enter the IPv6 parameter information in the local network according to the principle.

And other sensitive information.

(2) Configure IPv6 parameters from the command:

After the end of the configuration, the problem persists. The local computer still cannot access the IPv6 Site of the internal network.

Other XP computers do not have this question. So we use the command line method

Configure the IPv6 address. The detailed steps are as follows.

Step 1: Enter cmd in the running state, and right-click the command prompt to select "maintenance personnel

Run as administrator ", open the command line window, and enter netsh to execute the NIC

Parameter configuration.

Step 2: Enter the following commands in sequence to enable our IPv6 Configuration.

Netsh> int

Netsh> interface> IPv6

Netsh> interface> IPv6> isatap

Netsh> interface> IPv6> isatap> set router xxxxxxx

(Replace xxxxxx with the IPv6 route address of the local network)

Netsh> interface> IPv6> isatap> set state Enabled

Netsh> interface> IPv6> isatap> quit

(3) Configure IPv6 from the service:

After the end of the configuration, I tried to access the Internet again and still did not handle the problem. It seems that the two methods have the IPv6 attribute

The row correction does not help. The problem still persists after the correct host file is copied on the Internet.

There is no IPv6 Configuration today, and we will continue to look for answers to our questions from the system.

I thought that when I used the XP system, a printing was formed because the netshare service was disabled.

Machine cannot be shared, so the smart machine plans to do it from the "service ".Article. Suggestion

In the displayed window, enter services. MSC to enter the "service" option window.

Compared to Windows 7 and Windows XP services, Windows 7 and Windows XP services are different.

This is a service called IP helper. It is determined that the Service plays a role in "IPv6 conversion technology,

If the service is terminated, the computer will not have the enhanced connectivity advantage provided by these technologies.

The corresponding IP Helper Service in Windows 7 is not in the startup mode.

After the upgrade, the IPv6 education site will be accessed again without any questions. Then, the service will be started.

The method is set to automatic. After the Windows 7 operating system is restarted, the problem is handled on Thursday.

Iii. Summary:

In Windows 7, the service named IP helper is used for IPv6 address analysis and access.

It corresponds to the IPv6 Helper Service in the Windows XP system. Suppose we do not use

For IPv6 Access, you can disable the above services. Suppose you want to use the IPv6 network.

It must be opened. In this troubleshooting example, the IP address in Windows 7 is

An IPv6 Website access error occurs when the Helper Service is Disabled unexpectedly. We look forward to you at it168

You can understand the new services in the Windows 7 operating system.

Fast Time positioning.

Source: Network

PS. XP is still in use. This article has not been tested.

---------------------------- Separation line at the end of the article ---------------------------- about me:
QQ space http://603117269.qzone.qq.com
Sina Blog http://blog.sina.com.cn/dahaiblogs

Article tags: windows7, IPv6 Configuration