Puling tl-wdr5600 V2.0 How to set up a wireless bridge

General tl-wdr5600 V2.0 set up wireless bridging step One, wireless bridge topology map

After the main and auxiliary routers set up the wireless bridge, the wired and wireless terminals can connect the main and the auxiliary routers to the Internet, and the mobile can automatically switch and realize roaming. Topology is as follows

tl-wdr5600 V2.0 Router Wireless bridging topology

Puling tl-wdr5600 V2.0 Set up a wireless bridge step two, determine the wireless signal that is bridged

Before setting up tl-wdr5600 for bridging, you need to know the wireless signal name and wireless password that is bridged, the wireless name and password of the primary router, as shown in the following figure

Confirm the wireless name and wireless password for the primary router

Puling tl-wdr5600 V2.0 Set up wireless bridging step three, enter the tl-wdr5600 Bridge settings page

1, Login to the Settings page

The computer uses the network cable to connect to the LAN port of the tl-wdr5600 router, then enters the tplogin.cn in the browser, enters the login password, logs on to tl-wdr5600 's setup page

Log on to the TL-WDR5600 settings page

2, open the Bridge settings page

Click "Apply Management"

Click "Apply Management"

Locate the wireless bridging option, and then click Enter

Wireless Bridge setup options for entering tl-wdr5600

Puling tl-wdr5600 V2.0 Set up a wireless bridge step four, tl-wdr5600 Wireless bridge settings

1. Start Setup Wizard

When you enter the Wireless Bridging Setup Wizard, click Start settings as follows

Start the Setup Wizard

2. Scan Wireless Signal

tl-wdr5600 Router automatically scans peripheral wireless signals

tl-wdr5600 Router automatically scans peripheral wireless signals

3, select the main router signal

Select the main router signal to scan and enter the main router's wireless password and click Next

Select Main Router signal

Pay attention to the problem

If the primary router signal is not scanned, verify that the primary router is on, and try to reduce the distance between the primary and secondary routers.

4. Confirm Admin IP Address

The primary router assigns an IP address to the secondary router for subsequent management of the router, and it is recommended that you write down the IP address and click Next.

To modify the tl-wdr5600 LAN port IP address

5. Set up the wireless password of the auxiliary router

Set the wireless network name and wireless password for the tl-wdr5600 router and click "Next"

Set the wireless network name and wireless password for the tl-wdr5600 router

Important Notes

We recommend that the wireless network name and wireless password of the tl-wdr5600 router be set to match the 2.4G wireless network name and wireless password on the main router, so that wireless roaming can be realized.

Puling tl-wdr5600 V2.0 Set up a wireless bridge step five, check that the tl-wdr5600 wireless bridge settings are successful

Once again enter the "Application Management"--> "wireless bridging"--> can see "Bridge status is", if the display bridge succeeds, the tl-wdr5600 V2.0 router's wireless bridge setup succeeded.

tl-wdr5600 Wireless Bridge Setup succeeded

This tl-wdr5600 wireless bridging (WDS) Setup completes, the wireless terminal connects the Zhangsan, the wired computer connects the main, the auxiliary router's LAN port to be able to surf the Internet. In the process of terminal movement, automatic roaming between main and secondary routers can be realized.

Pay attention to the problem

(1), 5G Wireless network can only connect with the 5G wireless Network Bridge settings, that is, the main router must be the wireless network should be 5G band, before the 5G wireless bridge settings. If the primary router provides only 2.4G wireless networks, you cannot use a 5G wireless network on the tl-wdr5600 router to bridge, and you can only use the 2.4G wireless network to bridge the main router.

(2), dual-frequency routers can not be at the same time between 2.4G and 5G Bridge.

(3) All operations of wireless bridging (WDS) are performed at the secondary router (in this case the tl-wdr5600 router) without setting up the main router