Quick completion of Wireless Broadband Router Installation

How to install a valid Wireless Broadband Router? I believe that many users do not have a special understanding of this, and the installation steps are very important, especially regarding security considerations. I hope you will get some insights after reading this article, and I hope this article will teach you more things.

A. First, connect the power connector to the power hole on the back of the DI-624, and then connect the other end to the power outlet. Wait about 30 seconds until the DI-624 is activated before proceeding to the next connection action. After the operation is correct, the power LED will be on.

B. Connect the network connection to the DSL/Cable Modem to the DI-624 WAN port (WAN ). The WAN indicator is on.

C. connect a network connection with a computer or device to any port of LAN port 1-4 (LAN), and insert the other end to the edible Ethernet port of your computer, the computer can be used to configure the DI-624. After the connection is correct, the LAN port light inserted into the network cable will be on.

D. Take the computer with the wireless Nic installed supporting 802.11b/g) near the DI-624, the wireless network settings for the wireless nic and the DI-624, see the instructions below.

Wireless Broadband Router installation Step 2: connect other computers to DI-624 Wireless Broadband Router
 
With other ethernet cables, connect other computers with Ethernet interfaces that require access through the DI-624 Wireless Broadband Router to the remaining three lanports on the rear panel of the DI-624; you can also take computers with wireless NICs installed near the DI-624 to access the Internet through the DI-624 Wireless Broadband Router.

Step 3 of Wireless Broadband Router installation: correctly configure your wired computer network settings

A. Right-click your computer desktop and select "properties" from the shortcut menu ".
B. In the subsequent window, right-click the network neighbor and select "properties ".
C. Select Internet protocol TCP/IP in the window that will be opened later, and click "properties" with the mouse ".
D. In the subsequent window, select automatically obtain the IP address and automatically obtain the DNS server address.
E. when the local connection shows that the vro is connected, check whether the vro is actually connected to your computer. In the run box of the Start Menu, Enter cmd, ping 192.168.0.1, and press Enter. If you can get the result, it means that your above configuration is correct and the computer has been connected to the DI-624. If not, refer to the documents in the FAQ for troubleshooting.

Step 4 of Wireless Broadband Router installation: correctly configure DI-624 Wireless Broadband Router

1. Open the Web browser, type http: // 192.168.0.1 in the address bar, and press Enter.
2. In the subsequent logon window, enter the username admin. The password is blank by default, and then click OK ".
3. In the subsequent window, click "Run Wizard" online settings Wizard ).

A. Select "Next ).

B. set your new password. You can also click Next without setting it. Although the password appears to have a numerical value by default, it is displayed only for the sake of security, the management password is empty by default and does not exist.

C. Set the time zone and select it based on your time zone. This article is based on the time zone of the China region, and then click "Next" Next ).

Step 5 of Wireless Broadband Router installation: DI-624 Wireless Broadband Router Select Internet connection type

In the previous dialog box, click Next to automatically detect the WAN connection status. You can also select it by yourself. The optional WAN connection types are listed in the pop-up dialog box below. Please select according to your actual network environment. The following describes the three main connection types.

A. if you select A dynamic IP address, follow these steps. Click Next. Click Next. For more information, see the Wireless Configuration Wizard in Step 6.

B. If your ISP gives you a fixed IP Address, select Static IP Address ). Enter the IP address, subnet mask, gateway address, and preferred DNS server address provided by the ISP. After entering the information, click "Next". For more information, see the Wireless Configuration Wizard in Step 6.

C. If you use an ADSL modem to access the Internet, select "PPPOE ". Enter the account name and password provided by your ISP, and then click Next. Enter the user name and password provided by your ISP, and press "Next"). Next, you can refer to the wireless setup wizard in Step 6.

D. If you select "Other WAN types", you can use the following networking methods. The steps are similar to those in the previous three steps.

Step 6 of Wireless Broadband Router installation: DI-624 Wireless Settings

After the WAN port connection mode is selected and configured, configure the wireless connection. Set wireless connection. By default, the SSID is default and the Channel is 6. You can change the SSID here to determine the name that uniquely identifies your wireless network; if you are in China, retain the default channel value. Click "Next" Next) to set the WEP Security mode.

By default, wireless encryption is Disabled.) If it is not Enabled, you can click Enabled to activate it. The next step is to select the encryption method. WEP has two options: 64Bit and 128Bit. For 64Bit, you must enter ten passwords in the Key, for-Bit mode, you must enter the 26-bit password in the Key, the entered password should be combined from the number 0-9 and the letter A-F. Click "Next" Next after setting ). If you do not want to encrypt your wireless device, you can keep the default status and click "Next" Next ). The following page shows that the configuration has been completed and needs to be restarted to make the configuration take effect. Click "Restart" to Restart ). The system automatically restarts. Click Close when the following page appears) to automatically save the settings and restart the device. At this point, the basic configuration of the DI-624 has been completed.

Step 7 of Wireless Broadband Router installation: configure a computer with a wireless network card to access the Internet

The following is an example of how to use the Windows built-in wireless management program to connect to the DI-624 using the instructions for use ):

1. make sure that the wireless function of your notebook has been enabled. One is to enable it hard, that is, there is a wireless signal switch button on or around the laptop keyboard, 2. Check whether the wireless network card is enabled in the hardware manager. In the lower-right corner of the desktop, you can press the left mouse button twice

2. click Refresh. At this time, the wireless network adapter searches for all wireless networks in the current environment. After the search is complete, you will see a wireless network with the SSID test624 modified in the Wireless Configuration just now. If you have not modified the SSID, the DI-624 default wireless network name is default, that is, DI-624 wireless router!

3. If encryption settings are performed in the DI-624 Wireless Settings, click Connect to pop up the dialog box to add a key, that is set in the DI-624, and then click OK.

4. The connection to the wireless network is displayed. For other settings or information, see "Advanced Settings", "Tools", and "system status ".