Raspberry Pi +8187l install kali Linux run pin

The use of academic exchanges, small partners do not mess with OH

Raspberry Pi a TP mini network card a 8187L Carro (a treasure boss no 3070) TF card One (8G or more)

3070 smaller and Raspberry Pi better fit or use omni-directional antennas This time, I'm using orientation.

Use TP Mini Card to do AP a 5V2A charging treasure a small schoolbag in the schoolbag it is best to use omni-direction antennas. Connecting to the Raspberry Pi with a mobile phone can achieve some special infiltration

Finally, let's show you the last picture.

First go to download Kali Linux address: https://www.offensive-security.com/kali-linux-vmware-arm-image-download/

Write TF card with Win32_disk_imager

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/AD/wKiom1YDri6xbL-dAADrDyFFm2M072.jpg "title=" 11.png "alt=" Wkiom1ydri6xbl-daadrdyffm2m072.jpg "/>

Insert the TF card into the Raspberry Pi and connect all the components to the power supply.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/AA/wKioL1YDrw7Rr2DjAAJaZWohRbE406.jpg "title=" 12.png "alt=" Wkiol1ydrw7rr2djaajazwohrbe406.jpg "/>

Use SSH connection (if you know IP, do not know please Baidu, Baidu can find)

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/73/AA/wKioL1YDr8nT3xbWAAQHNj93rR8468.jpg "title=" 1.png " alt= "Wkiol1ydr8nt3xbwaaqhnj93rr8468.jpg"/>

I have connected three network card wlan0 is 8187L (can be seen with Iwconfig)

Use Airmon-ng to start your network card name

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/AA/wKioL1YDsL-wmJwVAAGi2O6rA1c510.jpg "title=" 22.png "alt=" Wkiol1ydsl-wmjwvaagi2o6ra1c510.jpg "/> In the ifconfig to see the name of the network adapter card changed to remember the new name under the use of 8187L when the new name

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/AA/wKioL1YDsW3SblN9AAM_3ZviAng129.jpg "title=" 33.png "alt=" Wkiol1ydsw3sbln9aam_3zviang129.jpg "/>

Then use Airodump-ng Wlan0mon to start listening.

(

You may not be able to use it, restart the NIC

Ifconfig Wlan0mon Down

Iwconfig Wlan0mon Mode Monitor

Ifconfig Wlan0mon up

)

Airodump-ng Wlan0mon started listening.

Now you can capture a lot of signals, do not be happy too early, according to the above Airodump search for the wireless signal, and then can pick a strong signal to crack (that is, the lower the value of the PWR column, the better) also not all can run pin (MB this column 54e. There's this "." To run a pin) now pick a signal strong use the Reaver command

Another thing: Remember Bssid (is the router's Mac) CH (channel, also can not) ESSID (the name of the WiFi, or you do not know that you run the WiFi is funny)

Of course, you need to install Apt-get installed Reaver first.

Reaver-i mon0-b 00:00:00:00:00:00-a-s-vv-d2-t 5-c 11

Network card used by-I

-B MAC Address

-A automatically detects the optimal configuration of the target AP

-S uses the smallest DH key to improve PJ speed

-VV show more non-critical warnings

-D that is, delay is set to 1 seconds per poor time

-T is the maximum time that timeout waits for feedback each time, if the signal is good, you can # # #设置

-C channel is the value of CH can be added without adding

All you have to do is wait for TA to finish ...

Family

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/AF/wKiom1YDuc-T7LSYAAgFygO4CYY208.jpg "title=" 55.png "alt=" Wkiom1yduc-t7lsyaagfygo4cyy208.jpg "/>

This article from the "Romantic Smile" blog, reproduced please contact the author!

Raspberry Pi +8187l install kali Linux run pin