Router does not recognize ADSL module solution

After the router installed on the WIC-1ADSL system can not see the port atm0, in general, because the IOS version is not supported, such as 2600 on the C2600-i-mz.122-8.T5.bin is not supported, then there will be some error prompts, such as display 00: 00: 09: % SYS-2-GETBUF: Bad getbuffer, bytes = 68444513

-Process = "init", IPL = 0, pid = 2

-Traceback = 80378168 8081667c 80816568 8041bbc4 8041bdc0 8041c0b8 803142ec 803e9

1 C4 unplugging the card will not show this;

At this time you can upgrade iOS, such as flash: c2600-ik8s-mz.122-11.T.bin is certainly good;

When the show run operation is normal, the following similar display is displayed:

Interface atm0/0

No IP Address

Shutdown

No atm ilmi-keepalive

DSL operating-mode auto

Show ver can also display the module information as follows:

Cisco Internetwork Operating System Software

IOS (TM) c2600 software (C2600-IK8S-M), version 12.2 (11) T, release software (FC1)

TAC support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by Cisco Systems, Inc.

Compiled Thu 01-aug-02 16: 56 by ccai

Image text-base: 0x8000809c, data-base: 0x817dafd8

ROM: System Bootstrap, version 12.2 (7R) [cmong 7R], release software (FC1)

Jngs uptime is 4 minutes

System returned to Rom by power-on

System image file is "Flash: c2600-ik8s-mz.122-11.T.bin"

Cisco 2621xm (mpc860p) processor (Revision 0x100) with 60416 K/5120 K bytes of mem ory.

Processor board ID jpe072410l3 (3444616740)

M860 processor: part number 0, mask 32

Bridging software.

X.25 software, version 3.0.0.

2 fastethernet/IEEE 802.3

2 fastethernet/IEEE 802.3 interface (s)

1 atm network interface (s)

32 K bytes of non-volatile configuration memory.

32768 K bytes of processor board system flash (read/write)

Configuration register is 0x3922

Whether the module is easy to use can be preliminarily determined through show diag

Shown below

Slot 0:

C2621xm 2Fe mainboard port adapter, 3 Ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision: 1.0

PCB serial number: jpe072410l3 (3444616740)

Part number: 73-7754-02

RMA history: 00

RMA number: 0-0-0-0

Board revision: A0

Deviation number: 0-0

EEPROM format version 4

EEPROM contents (HEX ):

0x00: 04 FF 40 03 6D 41 01 00 C1 18 4A 50 45 30 37 32

0x10: 34 31 30 4C 33 20 28 33 34 34 34 36 31 36 37 34 & n

Bsp; 0x20: 30 29 82 49 1E 4A 02 04 00 81 00 00 00 00 42 41

0x30: 30 80 00 00 00 00 FF

0x40: FF

0x50: FF

0x60: FF

0x70: FF

WIC slot 0:

Dsl sar (ADSL) clearly shows the hardware

Hardware revision: 2.3

Part number: 73-4771-08

Board revision: A0

Deviation number: 0-0

Fab Version: 05

PCB serial number: jab061509qz

RMA test history: 00

RMA number: 0-0-0-0

RMA history: 00

EEPROM format version 4

EEPROM contents (HEX ):

0x00: 04 FF 40 00 2E 41 02 03 82 49 12 A3 08 42 41 30

0x10: 80 00 00 00 00 02 05 C1 8B 4A 41 42 30 36 31 35

0x20: 30 39 51 5A 03 00 81 00 00 00 04 00 FF

0x30: FF

0x40: FF

0x50: FF

0x60: FF

0x70: FF

ArticleInput: CSH responsible editor: CSH