After the router installed on the WIC-1ADSL system can not see the port ATM0, in general, because the IOS version is not supported, such as 2600 on the C2600-i-mz.122-8.T5.bin is not supported, then there will be some error prompts, such as display 00: 00: 09: % SYS-2-GETBUF: Bad getbuffer, bytes = 68444513
-Process = "Init", ipl = 0, pid = 2
-Traceback = 80378168 8081667C 80816568 8041BBC4 8041BDC0 8041C0B8 803142EC 803E9
1 C4 unplugging the card will not show this;
At this time you can upgrade IOS, such as flash: c2600-ik8s-mz.122-11.T.bin is certainly good;
When the show run operation is normal, the following similar display is displayed:
Interface ATM0/0
No ip address
Shutdown
No atm ilmi-keepalive
Dsl operating-mode auto
Show ver can also display the module information as follows:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK8S-M), Version 12.2 (11) T, release software (fc
1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 01-Aug-02 16: 56 by ccai
Image text-base: 0x8000809C, data-base: 0x817DAFD8
ROM: System Bootstrap, Version 12.2 (7r) [cmong 7r], release software (fc1)
Jngs uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash: c2600-ik8s-mz.122-11.T.bin"
Cisco 2621XM (MPC860P) processor (revision 0x100) with 60416 K/5120 K bytes of mem
Ory.
Processor board ID JPE072410L3 (3444616740)
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3
2 FastEthernet/IEEE 802.3 interface (s)
1 ATM network interface (s)
32 K bytes of non-volatile configuration memory.
32768 K bytes of processor board System flash (Read/Write)
Configuration register is 0x3922
Whether the module is easy to use can be preliminarily determined through SHOW DIAG
Shown below
Slot 0:
C2621XM 2FE Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision: 1.0
PCB Serial Number: JPE072410L3 (3444616740)
Part Number: 73-7754-02
RMA History: 00
RMA Number: 0-0-0-0
Board Revision: A0
Deviation Number: 0-0
EEPROM format version 4
EEPROM contents (hex ):
0x00: 04 FF 40 03 6D 41 01 00 C1 18 4A 50 45 30 37 32
0x10: 34 31 30 4C 33 20 28 33 34 34 34 36 31 36 37 34
& N
Bsp; 0x20: 30 29 82 49 1E 4A 02 04 00 81 00 00 00 00 42 41
0x30: 30 80 00 00 00 00 FF
0x40: FF
0x50: FF
0x60: FF
0x70: FF
WIC Slot 0:
Dsl sar (ADSL) clearly shows the hardware
Hardware Revision: 2.3
Part Number: 73-4771-08
Board Revision: A0
Deviation Number: 0-0
Fab Version: 05
PCB Serial Number: JAB061509QZ
RMA Test History: 00
RMA Number: 0-0-0-0
RMA History: 00
EEPROM format version 4
EEPROM contents (hex ):
0x00: 04 FF 40 00 2E 41 02 03 82 49 12 A3 08 42 41 30
0x10: 80 00 00 00 00 02 05 C1 8B 4A 41 42 30 36 31 35
0x20: 30 39 51 5A 03 00 81 00 00 00 04 00 FF
0x30: FF
0x40: FF
0x50: FF
0x60: FF
0x70: FF