Router Installation and Use: analyze the four steps of the router Installation Guide

Wireless Router Installation Guide

1. confirm that the broadband line is normal: the wireless router installation guide allows you to connect your computer's shared high-speed broadband network to the Internet; however, before that, you must first have an Ethernet-based Cable/DSLModem (using a RJ-45 connector) and make sure that your broadband network is only connected to one computer, you can connect to the Internet as provided by the network service provider (ISP.

2. Delete the dial-up software: We recommend that you use the Windows/XP/Windows operating system to set up a wireless router. If you are using the Windows 98se2/ME operating system, if you have installed the ADSL dial-up (No.) software provided by the ISP, delete it before starting the connection settings in the wireless router Installation Guide.

3. System Requirements: This product uses a browser for setup and installation. No additional programs are required for connection, we strongly recommend that you upgrade your browser to InternetExplorer5.5/SP1 SP1 or later versions before you start setting. You do not need to connect to the Internet. You only need to use a local area connection (LAN) to set up a wireless router Installation Guide. The hardware of the wireless router only needs to be set once, And the rest only needs to be set through the computer or device of the wireless router.

Demonstration of hardware device connection settings

◆ Connect the power connector to the power hole on the back of the wireless router, and connect the other end to the power outlet. Wait about 30 seconds until the wireless router is activated.

◆ Connect the network line connecting to ADSL/CableModem to the WAN port ).

4. After the connection settings are completed, the wireless router indicator should be:

◆ Power lights are always on.

◆ The Status light flashes every second.

◆ The WAN light flashes from time to time.

◆ WLAN lights flash.

◆ LAN1-4 indicator flashing.

5. Take the computer or device that has installed the wireless network card near the wireless router. the wireless network between the wireless network card and the wireless router can detect the signal strength. It is applicable to Windows, XP, and Windows operating systems.

1. Connect the ADSL line to the WAN port of the wireless router and connect the network line of the NIC to the lanport. (1 ~ 4 port, any one port ).

2. Set the computer's InternetProtocol (TCP/IP) in the router Installation Guide ):

◆ First, right-click the "Network Neighbor" icon on the desktop and select "properties 」.

◆ Select the "local connection" icon and right-click and select "properties 」.

◆ Select Internet Protocol (TCP/IP) and click "properties 」.

◆ In the Internet Protocol (TCP/IP) attribute, change to "use the following IP Address" and "use the following DNS server address", and enter the IP address in sequence: 192.168.0.100 and subnet mask: 255.255.255.0, Default Gateway: 192.168.0.1, preferred DNS server: 168.95.1.1, and press OK.

Iii. vro Installation Guide to check whether the computer has obtained the correct IP Address:

◆ Go to start & #1048774; run in open field, enter "cmd", and press OK.

◆ Enter DOS mode, Enter "ipconfig", and press Enter. Check whether the "IPAddress" IP address, "SubnetMask" subnet mask, and "DefaultGateway" Default Gateway match the TCP/IP in the NIC.

If not, run the following actions:

◆ Right-click "Network neighbors" on the desktop and select "properties 」.

◆ Right-click Local Connection and choose disable 」.

◆ After the local connection is disabled, right-click Local Connection and select enable 」.

Note:

◆ You can also use DHCP to automatically assign IP addresses. In the "TCP/IP" setting item, select "automatically obtain IP addresses" and "automatically obtain DNS server addresses.

◆ If you have multiple computers, you can use DHCP to automatically assign IP addresses. Or use the above steps to specify the IP address, but note that the IP addresses of each computer cannot be the same. Set the IP address to 192.168.0.2 ~ The value range is 192.168.0.254.

4. Set Internet Explorer in the router Installation Guide:

◆ Return to the desktop and click "InternetExplorer.

◆ Press "stop", select "Tools", and click "Internet Options 」.

◆ Select the connection interface and confirm that the content in dial-up and VPC settings is blank. If the project contains other information, delete it. Then, press "LAN Settings 」.

◆ Confirm that all settings on the "LAN Settings" interface are blank. Then, press "OK" and then press "OK" to exit.

◆ Open IE, Enter 192.168.0.1 in the URL column, and then press Enter 」.

◆ Enter the user name and password. User name: admin Password: blank (do not enter any characters) and press "OK" to go to the wireless router configuration page.

◆ Complete.