SAS hard disk installation Windows 7 how to

Installing Windows 7 using the SAS hard drive with the Intel onboard Blue SCU interface requires the drive to be loaded with a USB flash drive, as follows:

First determine the system version, open the following link to download the driver:

Windows 7 32-bit:http://think.lenovo.com.cn/support/driver/driverdetail.aspx?deditid=7545

Windows 7 64-bit:http://think.lenovo.com.cn/support/driver/driverdetail.aspx?deditid=7546

After the download is complete, double-click on, click "Next", tick "I accept the Agreement", click "Next", make a note of unzip the directory and then click "Next", "Install", "Finish".

Open the extracted directory and copy the following folder to the USB flash drive:

Windows 7 32-bit:

C:\SWTOOLS\DRIVERS\IRST\W1RST32WS13_F6\RSTe_f6_iaStorS_win7_32

Windows 7 64-bit:

C:\SWTOOLS\DRIVERS\IRST\W1RST32WS14_F6\RSTe_f6_iaStorS_win7_64

Put the system disk into the optical drive, theUSB stick plug the Black USB2.0 interface behind the chassis , press the F12 button to bring up the boot menu continuously.

If you are installing a Windows 7 32-bit system, select the optical drive directly by pressing ENTER, as shown in.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6C/5A/wKiom1VHDhWBoKUmAAIWDQ0UuOU408.jpg "/>

If you are installing a Windows 7 64-bit system, the menu shown may appear.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6C/5A/wKiom1VHDhbyQqHEAAFr1vd727Y525.jpg "/>

It is important to note that depending on the size of the hard disk to select the corresponding startup items, if you want to install the system's hard disk capacity (including group raid) less than 2TB, Select the legacy beginning of the optical drive entry , Press a few enter .

If it is larger than 2TB, it is recommended to select the CD-ROM entry at the beginning of Uefi and press ENTER.

Attention:

1, If the hard disk is larger than 2TB, in legacy mode installation system, the hard disk can only use MBR partition table format, but the MBR maximum support 2TB, will cause 2TB after the hard disk space can not be used, then you must use the GPT partitioned table format. However, the legacy mode does not support GPT hard disk as the hard disk to install the system, it must be booted with UEFI mode, and Windows 7 32 does not support UEFI, so it is recommended to install the Windows 7 64-bit system for full use of the hard disk;

2, if the hard disk to install the system is less than 2TB but the other hard disk than 2TB, both modes can be , because both modes support GPT hard disk as a data disk.

3. Some windows 7 64-bit system disks do not have a UEFI boot module, and if the spoke startup item shown does not appear, the system disk does not support UEFI boot, Please change to another version of the system disk .

When you are done with the steps shown, click "Load Driver".

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6C/56/wKioL1VHD4WwhNaDAAHKmQ_MGBY649.jpg "/>

Click "Browse", select the drive folder on the USB drive, and click "OK".

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6C/5A/wKiom1VHDhfxs8LMAAMdyw3Rj9U936.jpg "/>

Tick "Hide drivers that are incompatible with hardware on this computer."

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6C/56/wKioL1VHD42DiMxIAANSrhw2C1o661.jpg "/>

Click "Next".

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6C/5A/wKiom1VHDiihz728AAJzFgmA5_Q478.jpg "/>

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6C/56/wKioL1VHD5_SHoYiAAKNeY_VVVY751.jpg "/>

After the driver is loaded successfully, the system can recognize the hard drive and then install the system properly.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6C/56/wKioL1VHD6fwu6AwAAKRrM0snO8309.jpg "/>

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6C/5A/wKiom1VHDkHwLaWIAAKOvVoYpQQ394.jpg "/>

This article from "It Technology Learning and communication" blog, declined reprint!

SAS hard disk installation Windows 7 how to