Simulation of cisco router with dynamic in Linux (1)

Environment: centos5.2

Software: dynamic. cisco-ios

1: Download the dynamic binfile.

Wget http://www.ipflow.utc.fr/dynamips/dynamips-0.2.6-RC4-x86.bin

Music dynamips-0.2.6-RC4-x86.bin/usr/local/bin/dynamips

2: install the required libs.

Wget http://www.mr511.de/software/libelf-0.8.10.tar.gz

Compile and install:

./Configure -- enable-gnu-names

Make-j7 DEPSHALIBS = "-lc"

Make install

Cp-r/usr/local/lib/libelf. so.0/usr/lib/

Cp-r/usr/local/lib/libelf-0.8.10.so/usr/lib/

3: Download the ios file. Here I will use the 3640 route as an example: (other ios will download it by myself. According to the dynamics version, we can see the supported ios)

Wget ftp: // wolf: colorwolf5768@ftp.microwolf.net/nettools/ios/c3640-i-mz.122-13.T1.bin

4: Start dynamips and initialize the route:

The usage is as follows:

Dynamips-P <routing type to be simulated>-p Slot Number: Module name <ISO file name of the corresponding route>

The type of the route. Currently, it can be 7200, 3600, 2691, 3725, or 3745. The default value is 7200.

-P is followed by the slot number: Module name, indicating that the port module is inserted in the physical slot starting from 0). For specific command usage, see the official documentation.

Next we will simulate a Cisco 3640 instance. slot0 is connected to a fast Ethernet board, and slot1 is connected to a 4-port E1.

Dynamips-P 3600-p: NM-1FE-TX-p 1: NM-4T c3640-i-mz.122-13.T1.bin

Cisco 7200 Simulation Platform (version 0.2.6-RC4-x86)

Copyright (c) Christophe Fillot.

Build date: Nov 15 2006 23:05:16

IOS image file: c3640-i-mz.122-13.T1.bin

CPU0: carved JIT exec zone of 64 Mb into 2048 pages of 32 Kb.

NVRAM is empty, setting config register to 0x2142

C3600 instance 'default' (id 0 ):

VM Status: 0

RAM size: 128 Mb

NVRAM size: 128 Kb

Chassis: 3640

IOS image: c3640-i-mz.122-13.T1.bin

Loading ELF file 'c3640-i-mz.122-13.T1.bin '...

ELF entry point: 0x80008000

C3600 'default': starting simulation (CPU0 PC = 0xffffffffbfc00000), JIT enabled.

ROMMON emulation microcode.

Launching IOS image at 0x80008000...

Self decompressing the image: ######################################## ############################### [OK]

Invalid iomem value in ROM (5). Smart-init will

Now run to compute a valid value

Iomem percentage may need to be reset manually

Smart Init is enabled

Smart init is sizing iomem

ID MEMORY_REQ TYPE

000044 0X0004FE00 Single Port Fast Ethernet

000054 0x0004e00004 T Mueslix Serial

0X000F3BB0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X003A2E30

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

Configuration or there is a software problem and

System operation may be compromised.

Rounded IOMEM up to: 4 Mb.

Using 3 percent iomem. [4 Mb/128 Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

Subject to restrictions as set forth in subparagraph

(C) of the specified cial Computer Software-Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(C) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.2 (13) T1, release software (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 03-Jan-03 :10 by ccai

Image text-base: 0x60008930, data-base: 0x60C1A000

Cisco 3640 (R4700) processor (revision 0xFF) with 126976 K/4096 K bytes of memory.

Processor board ID 00000000

R4700 CPU at 100 Mhz, Implementation 33, Rev 1.2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface (s)

4 Serial network interface (s)

DRAM configuration is 64 bits wide with parity enabled.

125 K bytes of non-volatile configuration memory.

8192 K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---