Solaris 10 installation Configuration

Solaris 10 installation configuration 1. system installation root/changeme creation user and password create/SP/users/scadmin set/SP/users/scadmin role = Administrator (Administrator privilege) scadmin/users/SP/users/scadmincd/SP/networkset pendingipaddress = 192.168.0.5set pendingipdiscovery = staticset topology = inclupendingipgateway = inclucommitpending = trueset state = enabledshow/SP/network start/SYS (system power-on, is equivalent to pressing the white power button in front of the Panel) start/SP/cons Ole-f (enter the system console to view the system power-on startup process) in the middle of show faulty, you need to set a root password to use root to enter the system, init 0 enters the OK mode. OK boot dvd can be installed remotely. Use zfs to create an image. nfs is released here until nfs kernel 2 and eis are selected for installation. /setup-standard.sh Note: Select 3 when selecting country code and then enter CN If the above selection is wrong, you can enter explorer to collect Log explorer-g to modify. generation 3, Series Install and read the readme file through patch. /installpatchset -- s10patchset defaults 4. configure root @ WOLF # cat/etc/hosts in IPMP :: 1 localhost 127.0.0.1 localhost 172.16.0.3 WOLF loghostroot @ WOLF # ls-l host *-rw-r -- 1 root 9 May 29 hostname. igb0-rw-r -- r -- 1 root 37 May 30 :26 hostname. usbecm0lrwxrwxrwx 1 root 12 May 29 14:10 hosts- >. /Inet/hostvi hostname. igb0 (Add the following content) WOLF netmask + broadcast + group ipmp0 uproot @ WOLF # vi hostname. igb1 (create hostname. add the following content to the igb2 file .) Group ipmp0 standby up limit 5. Enter system zfs to create and mount zpool listdf-hcd/usrmkdir localcd localmkdir bccpzpool listzpool statusformatprtvtoc/dev/rdsk/clusters | fmthard-s-/dev/rdsk/ c0t5000CCA03C710D10d0s2fmthard: new volume table of contents now in place. zpool create-f WOLFppool/dev/dsk/c0t5000CCA03C710D10d0s0zp Ool create-f WOLFpool/dev/dsk/export listzfs set mountpoint =/usr/local/bccp WOLFpoolzfs set mountpoint =/usr/local/mccp WOLFpooldf-h limit 6. Users and group root @ WOLF # bashroot @ WOLF # groupadd-g 100 scadaroot @ WOLF # useradd-u 1002-g scada-d/usr/local/WOLF WOLFuseradd-u 1002-g scada- d/usr/local/W OLF WOLFroot @ WOLF # pass WOLFpassmgmt passwd root @ WOLF # passwd WOLFNew Password: Re-enter new Password: passwd: password successfully changed for WOLFmkdir/usr/local/grouproot @ WOLF # chown-R bccp: scada/usr/local/groupchown-R mccp: scada/usr/local/grouproot @ WOLF # chown-R bccp: scada/usr/local/bccpchown-R mccp: scada/usr/local/mccp restart ------------------------------------------------------------- --------------------------- * 7. Hard Disk dd clone (problematic) prtvtoc/dev/rdsk/release | fmthard-s-/dev/rdsk/release if =/dev/dsk/c0t5000CCA03C70BBFCd0s2 of = dev/dsk/release bs = 1024 k limit 8, the root password is set incorrectly, set sys-unconfig to OK and then boot to set the system environment parameters.