Step by step Instruction-install Vixdiag Ford IDS V96 in Windows7

This is the instruction on what to install Vixdiag Ford IDS V96 in Windows 7 System.

Requirement:
Vxdiag VCX NANO for Ford

Parts:
Install Calibration
Install Ids-91.01-full
Install Ford-ids-96.01-full
Confirm IDS V96 function
Install Deep Freeze
Check If IDS V96.01 is installed correctly

Detailed steps:
Install Calibration
Insert V81 DVD.
Open "Computer->dvd RW Drive (E:) Ford IDS V81->vcmdvd ".
Select "Calibrations".
Click "Next".
Click "Next".
Click Install to begin the installation.
Installing .... (Please wait for until the software Complete installation. Usually it'll take about 30MIN-2H)
Calibration installation success.
Click "Finish" to exit the wizard.
Click The Exit button at the left bottom in VCM DVD interface.

Install ids-91.01-full
Insert V96 DVD.
Open "Computer->dvd RW Drive (E:) Ford IDS ".
Close the "AutoPlay" interface.
Open "Ids-91.01-full"
Choose Setup language. and click "Next".
Preparing Setup ...
Click "Yes" to proceed.
Click "Next".
Click "Next" with the selection of "I accept the terms of the license Agreement".
Destination:click "Next".
Click Install to begin the installation.
Installing .... (Please wait for until the software Complete installation. Usually it'll take about 30min-2h)
IDS icon on Desktop.
Configuring ...
Adobe SVG Viewer 3.0 Setup ...
Configuring ...
Updating the database ....
Configuring ...
successfully installed IDS.
Click "Reboot" to restart your computer.

Open "IDS" on Desktop.
Fill in the dealer Type/code, Country, and then click the Tick button to continue.
IDS software-computer Date synchronization, click "Continue".
Open it and you'll get message reading a non-renewable Evaluation License .... expire in 3 days.
(note:if you does not get the message below it means the installation fails and then does not continue to operate.)

Close IDS-91.1 interface. Click the Tick button.

Install Ford-ids-96.01-full
Open "Computer->dvd RW Drive (E:) Ford ids->ford-ids-96.01-full. "
Preparing Setup ...
Click "Yes" to proceed.
Click "Next" to update the installed IDS V91.01 to V96.01.
Installing .... (Please wait for until the software Complete installation. Usually it'll take about 30MIN-2H)
Configuring ...
Adobe SVG Viewer 3.0 Setup ...
Configuring ...
Updating the database ....
Configuring ...
Successfully updated IDS to version 96.01.
Click "Reboot" to restart your computer.

Open "IDS" on Desktop.
Close IDS-96.01 interface. Click The Tick button.

Open "Start" menu on Desktop. Start menu->software updates->control Panel.
Network and internet->internet and sharing Center
Change adapter settings (on left menu)
Wait for the communication complete.
Select "Local area Connection", and close the interface.

Confirm IDS V96 function
Open "IDS" on Desktop.
Start New Session->all Other. Click The Tick button.

Establishing communication to PCM ...
Select vehicle specification, and click the Tick button. e.g. the case here, select "MY".
Vehicle Specification:click "YES" to go on.
Click The Tick button.

Module programming.
Click The Tick button.

Read and exit.

Self Test.
Click The Tick button.

Select "All Cmdtcs" and click the Tick button.
Read and exit.

Datalogger.
Click The Tick button.
Powertrain->engine. Then click the Tick button.
Set the ignition switch to on, then to continue.
Click The Tick button.
Exit.

Delete (deletes session), then-go on.

Close the interface to exit IDS-96.01.

Install Deep Freeze
Note:after confirming IDs v96 software ' s diagnosis and programming function, You need to use DFSTD software to protect the installed IDs software partitioning. If the software is not protected, it'll expire after 3 days.
Open Computer->dvd RW Drive (E:) Ford ids->dfstd->dfstd. "
Click "Next" to install the deep Freeze.
Select "I Accept ..." and click "Next".
Open Computer->dvd RW Drive (E:) Ford Ids->dfstd->dfstd_key "To copy the key to" License key "for licensing. Then click "Next".
uncheck to thaw the drive, to continue.

Click "Install".
Restart your computer.

Check if IDS V96.01 is installed correctly
Open "IDS" on Desktop.
Start New Session->all Other. Click The Tick button.
Establishing communication to PCM ...
Select vehicle specification, and click the Tick button. e.g. the case here, select "MY".
Vehicle Specification:click "YES" to go on.
Click The Tick button.
(To see the functions as if you are confirming)

Done.

Step by step Instruction-install Vixdiag Ford IDS V96 in Windows7