Step-by-step instructions on configuring the ADSL Router

Before using a route, it is very important to do a good job of routing configuration. Here we mainly introduce the configuration of the ADSL Router, including some details. I often have friends ask, about the ADSL Router settings, in fact, the ADSL Router settings is not very difficult, take the TL-R4XX series router as an example.

Briefly describe the configuration of the ADSL Router. First, the MODEM, router, and computer are connected, and the network must be smooth. The default IP address of the ADSL Router address is 192. 168. 1. 1. subnet mask: 255. 255. 255. 0) Use a network cable to connect the LAN port of the router to the network card of the computer, because the Ethernet port on the router has the polarity automatic flip function, therefore, no matter whether your network cable uses a direct line or a line.

1. Enter the vro address 192.168.1.1 in the browser to enter the management interface.

2. Start configuring the vro

With the information preparation for the broadband access method at the beginning, it is much more convenient to configure. The vro management interface will pop up
A page similar to the setting wizard is displayed. Select next and follow the prompts.

3. If your broadband access method is ADSL PPPoE, set "WAN port connection type" to "PPPoE", and enter "Internet account" and "Internet password ", select "Automatic Connection" and click "save" to complete the configuration. After saving, the password entered in the "Internet password" box will be several more characters, this is dedicated for the sake of security, and the basic configuration of the ADSL Router is complete.

4. Configure the IP address of the ADSL Router: 192.168.1.11X in the range of 2-254.

Subnet Mask: 255. 255. 255. 0,
Default Gateway: 192. 168. 1. 1. After filling in, click "OK" twice.
Chongqing DNS: 61.128.128.68

5. Set the reboot mode to enable Internet access in the browser. The above is the most basic configuration of the ADSL Router. Sorry for the rush of time. I will add it later.

First, make sure that ADSL MODEM212 works properly, that is, we can use it to access the Internet. Then, we cut off the power of the computer and adsl modem, connect the TL-R402 Broadband Router in. It is a shared-access device developed specifically for home users and small offices. It is integrated with Four 10/100 Mbps switches for connecting user computers that require Internet access. The WAN port on the back panel is used to connect network access devices such as adsl mo-DEM. After the above connection, we need to make a simple configuration of the TL-R402 Broadband Router, so that it can replace the computer for automatic dialing.

A TL-R402 Broadband Router also has an IP address and uses Web Page Management. You can enter "http://xxx.xxx. XXX. XXX" in the address bar of IE browser to enter the management page to set the ADSL Router. TL-R400 factory default IP address is "192.168.1.1", subnet mask is "255.255.255.0 ". Note that entering "http: // 192.168.1.1" in the address bar of the computer's IE browser cannot access the management page. The principle is simple: the IP address must be in the same CIDR Block for access. Therefore, we must first modify the IP address of the local computer connection.

Enter the "TCP/IP properties" dialog box for "Local Connection" of any computer system in the LAN. In this dialog box, set the IP address to "192.168.1. X" (x is a natural number ranging from 1 to 253), and set the gateway to "192.168.1.1 ". After two consecutive "OK" operations, the settings take effect immediately. Now we can enter "http: // 192.168.1.1" in the IE address bar To Go To The TL-R402 Management page. On the logon page that appears, enter the default password "admin" in the left-side logon box to go to the Management page.

Next, click "Next" to change the WAN type to "PPPoE" (Point-to-Point Protocol on LAN), because ADSL dialing adopts this protocol. Here, we want to fill in the ADSL account and password (that is, the ISP provided to your ADSL user name and password), after the dial-up task is handed over to the TL-R402. After entering the information, save the settings. Enter "http: // 192.168.1.1" in the IE Address Bar and press Enter. Then enter the management password to enter the TL-R402 Management page and click the connection button in the status to initiate a dial-up connection. Wait about 5 seconds, the connection is successful, and the TL-R402 will display the obtained public IP address, isp dns server address and other information, now the client can access the Internet. Open IE and enter the URL -- GO !!

To access the Internet in the future, you only need to turn on the power of adsl mo-DEM and TL-R402, and TL-R402 will be automatically connected to the Internet by dialing. After logging on to the computer, you can directly access the Internet without any additional operations. If you don't want to access the Internet, turn off the power of the TL-R400. You can see the above picture, that is, virtual server settings: defines the ing between WAN service ports and LAN servers, and easily Forms WEB servers and FTP servers. If the Protocol IP address of your local TCP/IP connection is 192.168.1.2, then another user's host is 192.168.1.3, etc.