SYN5301 type mm stopwatch time calibrator

SYN5301 type mm stopwatch time calibrator

Part of the verification procedures:

First, technical requirements

The 1-second table is divided into one and tertiary according to the accuracy level, and its accuracy index

(The average correction value C and the allowable maximum deviation for each of the corresponding locations allowed) should not be greater than the values listed in table 1.

2 seconds after the watch is fully wound, the duration should be no less than the schedule.

The 3 second table must have the manufacturer's name and number.

Ii. Conditions of verification

4-Ring condition

4.1 Ambient temperature: 20±5℃.

4.2 Relative Humidity: 80% or less.

The 4.3-second table must be placed in the verification environment for more than one hour before verification.

5 Standard equipment

Any of the following standard equipment may be used for verification purposes (but no mechanical stopwatch is allowed for the calibration of mechanical stopwatch).

5.1 Second meter calibration device. The basic error does not exceed ±10ms.

5.2 Standard precision clocks. The daily difference does not exceed ±4s.

5.3 Quartz clock. The second hand beats at 1/2s or 1s, and can hear a clear seconds beat, and the accuracy of the crystal oscillator is better than 2x10-5.

6 check interval is the second dial and the full value of the sub-scale (such as the use of the stopwatch has special requirements, can be negotiated with the verification unit to resolve).

7 verification shall be carried out within the specified clockwork effective working time

Product Overview

SYN531 Stopwatch Time Calibrator is a high-precision time calibrator. This equipment is based on the requirements of jjg237-2010 "stopwatch verification procedures" of a multifunctional, comprehensive time verification automatic testing device for the verification of mechanical stopwatch, electronic stopwatch, pointer-type electric stopwatch, digital electric stopwatch, digital millisecond meter, and various timers, etc. Measured by measuring the standard time interval signal, the instrument is measured to measure the measured value of the standard time interval signal, so as to obtain the measurement error of the Ōō instrument, to achieve the purpose of verification, suitable for various types of stopwatch of the value of transmission, can establish a stopwatch calibration standard device, to carry out time-class instruments for verification/calibration.

Product Features

Can be used at all levels of measurement departments, factories, institutions and scientific research units 401/405 electric stopwatch, 407/408 stopwatch, 411 digital millisecond meter, 415/417/417b type digital stopwatch and other time-class instruments

Product Features

A) high precision, cost-effective;

b) Full-featured, reliable performance;

c) The use of high-stability quartz crystal oscillator as a time reference.

Typical applications

1) for the measurement departments at all levels, factories, colleges and scientific research units on mechanical stopwatch, electronic stopwatch, pointer-type electric stopwatch, digital stopwatch, digital millisecond meter and other timing instruments for verification.

2) used as the daily difference measuring instrument;

3) used as a standard time interval generator;

MM Stopwatch time Calibrator

Technical Index

Mechanical stopwatch and electronic stopwatch	Input Time range	300MS~9 999 999 999s
	Accuracy	Better than ± (1X10-7XT0+3MS)
	Physical interface	Banana seat
Pointer-type electric stopwatch	Input Time range	0.02S ~ 9 999 999 999s
	Accuracy	Better than ± (mains frequency accuracy xt0+0.6ms)
	Physical interface	Banana seat
Stopwatch and Digital Electric stopwatch	Input Time range	0.01μs ~ 9 999 999 999s
	Accuracy	Better than ± (1x10-7xt0+1μs)
	Physical interface	BNC
Crystal Oscillator Index	Frequency	10MHz
	Daily aging Rate	≤5x10-9/Day
	Second degree of stability	≤5x10-11/s
	Accuracy	≤1x10-7
	Warm-up time	12 hours
	50Hz	Large ones	1
		Level	Ttl
		Physical interface	DB9
	10MHz	Large ones	1
		Level	≥7dbm
		Physical interface	BNC
	RS232C Serial Port	Large ones	1-Way
		Level	rs232c
		Physical interface	DB9
Stopwatch Fixture	Test four stopwatch at a time to adapt to various shapes of stopwatch
Environmental characteristics	Operating temperature	0℃~+50℃
	Relative humidity	≤90% (40 ℃)
	Storage temperature	-30℃~+70℃
Power supply	AC 220V±10%, 50hz±5%, power less than 30W
Chassis dimensions	3u,19″ standard Chassis (upper frame) 482mm (w) x300 (deep) x140mm (h)
Options	Custom-made similar products according to customer requirements.

MM Stopwatch time Calibrator

Website: www.syn029.com

Contact person: well-off

Contact information: 18991937618

QQ : 2534240205

SYN5301 type mm stopwatch time calibrator