Teach you to configure DTU dual channel communication

Source: Internet
Author: User
Tags bit set

Connect a dual Hub server demo configuration for that WCTU

TCP mode Dual Center data transfer

Example description

This instance uses TCP mode to forward the data received by the serial port to the server and forwards the data sent by the server to the string. Data is not encrypted during transmission.

Reference Address: http://www.winertech.com/productinfo.asp?pid=396&WCTU3120

Configuring the server network

1. Confirm the external IP address or domain name of the native server

A, the IP address for the fixed IP leased line outside this instance is 220.160.156.233.

B, if the external network is a dial-up method, you need to use the domain name.

Condition One:

Through the peanut shell or other domain name resolution terminal bound external network IP

Condition Two:

If it is only a short time test communication, you can use the current extranet IP directly

Query the current extranet IP method: Search "IP" with Baidu

If there is a network through the router server can also be logged on the router, query the running state of the WAN Port current external IP

The IP addresses that are obtained are consistent if the inconsistency may have been translated by the carrier's internal network NAT and cannot be used as a server network.

2. Confirm the network structure of the server intranet, if the server is through the router Sisu network, please do port mapping or DMA on the router.

The port mappings made by this instance are as follows:

Example one:

Query the native server intranet IP as follows:

Windows7 system, Start > Control Panel > Network and Sharing Center > change adapter settings

Right-click Local Area Connection > Status > Details

3, if there is a router Sisu network, please confirm whether the firewall above the router open this port.

4, if a firewall is installed on the server PC, make sure the firewall is open for this port.

Device parameter Configuration

Open the Configuration tool: Open and debug serial port connected to the string number, baud rate, data bits, stop bit, flow control is the default value, the right prompt to open the serial port successfully power on the device, if the device has been powered, please re-power the device.

The configuration status is successfully entered after re-power on:

Configure the Hub server

Number of hub servers: 2

Center 1IP Address: The server's extranet address or domain name (220.160.156.233)

Center 2IP Address: The server's extranet address or domain name (weidejiaweige.vicp.cc)

Hub 1 Port: Server external network open port (30039)

Backup Hub port is: Server extranet open port (30040)

Communication serial parameters

Baud rate set to: 115200

Check bit set to: None

Data bit set to: 8

Stop bit set to 1

Protocol parameters

The communication protocol is set to: for that

Device ID is set to: FFFFFFFF

User ID is set to: 0000001

The packet response is set to: Enabled

The packet re-send interval is set to: 15

Packet re-send number set to: 3

The control pack response is set to: Enabled

The control pack restart interval is set to: 15

The number of times the control pack has been re-sent is: 3

The escalation protocol parameter is set to Enabled

Working parameters

The communication mode is set to: TCP

The network idle interval is set to: 60

Heartbeat packet interval is set to: 60

Other

Other parameters are set to factory settings.

Server Center Configuration

Registering Device information

Click the "Add Device Info" button. As shown in the following:

The registration management interface appears. As shown in the following:

Click on the "Add Device" button and the "Add Device" screen appears. As shown in the following:

Set the user ID and device ID that were consistent with the previous device. The user ID is set to 00000000, and the device ID is set to FFFFFFFF. As shown in the following:

Click Confirm to complete the setup and close the registration management interface.

Server parameter settings

Create a new two TCP server receive center

The server type is set to: TCP

Local ports are set to: 30039, 30040, respectively

The log path is set to: You can set the available paths arbitrarily

Other parameters Default

Click the "Confirm" button to start the service.

Communication test

Device connection

Restart the device and let the device connect to the server. When the device status light is blue and the device information is displayed on the server, the device is connected to the server. As shown in the following:

Teach you to configure DTU dual channel communication

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.