Technical Specifications of Gigabit Optical Fiber GBIC and SFP

Source: Internet
Author: User

1. What is GBIC?

GBIC is short for Giga Bitrate Interface Converter. It is an Interface device that converts Gigabit electrical signals into optical signals. GBIC is designed for hot swapping. GBIC is an Interchangeable product that complies with international standards. The gigabit switches designed with GBIC interfaces share a large market share due to flexible exchange.

2. What is SFP?

SFP is short for small form pluggable. It can be understood as an upgraded version of GBIC. The size of the SFP module is half that of the GBIC module. You can configure more than twice the number of ports on the same panel. Other functions of the SFP module are basically the same as those of GBIC. Some switch manufacturers call the SFP module A miniaturized GBICMINI-GBIC ). The size of the SFP module is half that of the GBIC module. You can configure more than twice the number of ports on the same panel. Other functions of the SFP module are basically the same as those of GBIC.

3. What types of optical fibers are used?

Multimode Optical Fiber is divided into two types: Multimode Optical Fiber and Single-Mode Optical Fiber. multimode optical fiber is widely used for short-distance communication because of its low cost and simple construction, multimode Optical Fiber is divided into two types: 50um core diameter and 62.5um core diameter. Among them, 62.5um is common, but its performance is not as good as 50um. Our GBIC-SX multimode products are suitable for these two multimode optical fiber, the transmission distance is 550 m on 50um optical fiber) and 330 m on 62.5um optical fiber ).

Single-Mode Optical Fiber is generally used for long-distance communication. The core diameter is 9um. Our single-mode GBIC products have a transmission distance of 10 km, 20 km, 70 km, and 120 km respectively on single-mode optical fiber. Generally, switch manufacturers only provide 10 km and 70 km models in a single mode. The 20 km product can effectively save the overall cost of the system integrator's specific network solution. The 120 km product is used in special ultra-long running environments.

Introduction to GBIC)

GBIC) is a hot swappable input/output device that is inserted into a Gigabit Ethernet port/slot to connect the port with the fiber optic network. GBIC can be used and exchanged on a variety of Cisco Products see Table 2), and can be port-by-port mixed with the 1000 BaseSX, 1000 BaseLX/LH, or 1000BaseZX interface following IEEE 802.3z. Furthermore, Cisco is providing a 1000 BaseLX/LH interface that fully complies with the IEEE 802.3z 1000BaseLX standard, but its transmission distance on a single-mode optical fiber is as high as 10 kilometers, it is 5 kilometers farther than the ordinary 1000BaseLX interface. In short, with the continuous development of new functions, it is easier to upgrade these modules to the latest interface technology, so that the customer's investment can maximize the benefits. A gbic is provided.

Gigabit Interface Converter

 

Generally, the GBIC module ports of different products have different requirements on the wiring specifications. Whether it is the wiring type or the wiring distance, the following analysis uses Cisco products as an example:



The following table lists the GBIC cabling specifications installed on the Gigabit Ethernet port. Note that all GBIC ports use SC-type connectors, and the minimum cabling distance of all listed GBIC multimode and single-mode optical fibers is 6.5 feet 2 meters ).

1: Only multimode optical fiber is used.

2: requires pattern adjustment to patch line CAB-GELX-625 or equivalent products ). If Multi-Mode Optical Fiber uses a general patch line, 1000 BaseLX/lh gbic and a short link several dozen meters away) will cause saturation at the receiving end, resulting in an error rate (BER) increase. In addition, if the LX/lh gbic is used with a 62.5 micron multimode optical fiber, you must install a pattern adjustment patch line between the GBIC at both ends of the link and the multimode optical fiber. If the link distance exceeds 984 feet 300), you also need to adjust the patch line in the mode.

Note: To comply with IEEE Standards, the pattern adjustment patch line CAB-GELX-625 or equivalent product must be used ). IEEE found that when some types of optical fiber inner cores are used, the link distance cannot meet the requirements. The solution is to use the mode call.(

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.