Set up wireless signal amplification mode (CLIENT+AP) online?
The first step: Configure the computer's IP address
Step Two: Configure the hot signal amplification mode.
Step three: Try the computer to surf the Internet?
The first step: the configuration of a good computer IP Address
Set the local connection IP address on your computer to " get IP address automatically"
1. Right-click on the desktop " Network Places ", select " Properties ":
2. Right-click "
Local Area Connection " and select "
Properties ":
3. Double-clickInternet Protocol (TCP/IP):
4. Select " automatically obtain IP address " " automatically obtain DNS server Address ", click " OK " and then click " OK" "can:
Step Two: Configure the wireless signal amplification mode.
Tip : The first use of routers, set up wireless signal amplification (CLIENT+AP) mode will appear in the process of Easy-to-use interface, you need to skip these interfaces, login to the Advanced Settings interface set up wireless signal amplification (CLIENT+AP).
1. In the browser address bar input:
http://tendawifi.com Press ENTER, login to the router setup interface, as shown below:
2. Click "
Skip this step " in the page, refer to the following figure
3. Set signal strength, router's wireless signal name and password, and set 5-32-bit router interface login password, click "
next ", refer to the following setup steps
4. "
Setup is complete , the
router is networked, please wait ...", wait about 10 seconds, click " more Features " in The Jump interface, refer to the following steps
5. Enter the set login password, click "
login ", enter the router's setup interface, refer to the following setup steps
6. After entering the router's setup interface, click on "
Wireless Settings " and select "
Universal Bridging " as follows:
7. Open "
Universal bridge
", bridge mode select "
Wireless signal Amplification (
client+ap
)", In the device automatically scan to the wireless signal to select the required relay of the superior wireless signal name, and enter the password, click "
save " reference to the following setup steps
8. Wait for the router to reboot after saving:
warm tip : In order to facilitate management, set up wireless signal amplification mode (CLIENT+AP), please set the device's login IP address and the superior device LAN port IP address the same network segment of different IP addresses, If the parent device's LAN port IP address is 192.168.2.1, change the login IP address of this device to 192.168.2.X (X is any value 2~254).
Step Three: View the wireless signal amplification (
Client+ap
) Whether to set a successful
Wait for the router reboot to complete, connect the router Lan1/lan2/lan3/lan4 interface, or reconnect the router wireless signal login Router settings interface, you can view the network status, "
extranet settings
" if displayed
Wireless signal Amplification (
client+ap
) mode bridged successfully ", indicating that the wireless signal amplification (CLIENT+AP) settings were successful.
Set up hot signal amplification mode (WISP) online?
Tip : The first use of the router, set up hot signal amplification (WISP) mode will appear in the process of Easy-to-use interface, you need to skip these interfaces, login to the Advanced settings interface set hotspot signal Amplification (WISP)
1. In the browser address bar input:
http://tendawifi.com Press ENTER, login to the router setup interface, as shown below:
2. Click "
Skip this step " in the page, refer to the following figure
3. Set signal strength, router's wireless signal name and password, and set 5-32-bit router interface login password, click "
next ", refer to the following setup steps
4. "
Setup is complete , the
router is networked, please wait ...", wait about 10 seconds, click " more Features " in The Jump interface, refer to the following steps
5. Enter the set login password, click "
login ", enter the router's setup interface, refer to the following setup steps
6. After entering the router's setup interface, click on "
Wireless Settings " and select "
Universal Bridging " as follows:
7. Open "
Universal bridge
", bridge mode select "
hot signal amplification (
WISP
)", In the device automatically scan to the wireless signal to select the required relay of the superior wireless signal name, and enter the password, click "
save " reference to the following setup steps
8. Wait for router reboot after confirmation:
Warm tip : If you click "OK", pop-up detection of IP conflict prompted information (as shown below), click "OK".
After waiting for the router to reboot, connect the router to the Lan1/lan2/lan3/lan4 interface, or reconnect the router to the wireless signal to try whether the Internet is normal. Login to the router's settings interface, you can view the network status, "
extranet settings
" If the display "Network
, you can surf the Internet ", indicating the success of the network settings, you can browse the Web, surfing the Internet. You can browse the Web and surf the Internet.
Warm tip : If there are other computers need to surf the Internet, direct the computer to the router Lan1/lan2/lan3/lan4 any free interface or connect the router wireless signal, refer to the second step will be local connection to automatically obtain IP address can, do not need to configure the router.
