The English meaning of the boot appears

When the boot will appear in English, you know the boot appeared in English meaning? These English phrases contain very important information, understand this information can solve some of their own small problems, but these English baffled a part of the friends, the following is the start of the English, we can understand.

1.CMOS Battery failed

It means the CMOS battery fails. This means that the CMOS battery is running out of power, just replace the new battery.

2.CMOS Check sum error-defaults loaded

This means that when the CMOS performs a full check, it finds an error and loads the system defaults. Generally speaking, it is said that the battery is running out of power, you can change the battery to try, if the problem is not resolved, then that the CMOS ram may have problems, if not a year to the dealer place to change a motherboard, after a year to let the dealer back to the manufacturer to repair it!

3.Press ESC to skip memory test

A memory check is in progress and can be skipped by pressing the ESC key. This is because there is no skip memory in the CMOS 第二、三、四次 test, the boot will perform four times memory test, of course, you can also press ESC to end the memory check, but every time this is too cumbersome, you can enter the COMs settings after the BIOS featurs setup, Set the quick power on Self test to Enabled and restart after storage.

4.Keyboard error or no keyboard present

The keyboard is wrong or the keyboard is not connected. Check if the keyboard connection is loose or damaged.

5.Hard Disk Install failure

Chinese: Hard drive installation failed. This is because the hard drive or cable may not be plugged in or the hard drive jumper is set incorrectly. You can check the root of the hard drive is plugged in, to see the same data line on the two hard disk jumper settings are the same, if the same, as long as the two hard drive jumper set to the same (one set to master, the other set to slave).

6.Secondary slave Hard Fail

Indicates that the detection failed from the disk. May be the CMOS settings, such as not from the disk but set in the CMOS from the disk, then there will be errors, then you can enter the COMs settings select IDE HDD auto detection for hard drive automatic detection. It may also be the hard drive's power cable, the data cable may not be connected or the hard disk jumper settings, the solution to refer to the 5th.

7.Floppy disk (s) fail or floppy disk (s) fail (80) or floppy disk (s) fail (40)

This is unable to drive the floppy disk drive. System prompts can not find the floppy drive, to see whether the floppy drive power cord and data cable is loose or wrong, or to the floppy drive on another machine to try, if these are not, then have to buy another, fortunately the floppy drive is not expensive.

8.Hard disk (s) diagnosis fail

An error occurred while performing a hard drive diagnostics. This problem generally means that the hard disk itself has failed, you can put the hard drive on another machine to try, if the problem is not resolved, can only go to repair.

9.Memory Test fail

Indicates that memory detection failed. Reseat the memory bar to see if it can be resolved, this problem is generally because the memory is incompatible with each other, to change a bar!

10.Override Enable-defaults Loaded

The current CMOS settings cannot boot the system and load the preset values in the BIOS to boot the system. Generally in the COMs set up error, as long as enter the COMs settings select Load Setup defaults load the original set of values and then restart it.

11.Press TAB to show POST screen

Press the TAB key to toggle the screen display. Some OEM manufacturers will be their own design of the display screen to replace the BIOS preset boot display screen, we can press the TAB key to the BIOS preset boot screen and the manufacturer's custom screen to switch between.

12.Resuming from Disk,press TAB to show POST screen

Restore the boot from the hard drive and press TAB to display the post screen. This is because some motherboard BIOS provides the suspend to disk (the hard drive hangs) the function if we use the suspend to disk the way to turn off the machine, then we will display this prompt message at the next boot.

13.Hareware Monitor found an error,enter power MANAGEMENT setup for details,press F1 to Continue,del to enter SETUP

Chinese: monitoring function found error, enter the power MANAGEMENT Setup to see the details, press F1 key to continue the boot process, press del key to enter COMs settings.

Explanation: Some motherboards have the hardware monitoring function, you can set the motherboard and CPU temperature monitoring, voltage regulator voltage output and monitor the speed of each fan, when the monitoring function in the boot found abnormal conditions, then the above paragraph will appear, then you can enter the COMs settings select Power MANAGEMENT SETUP, on the right side of the **fan monitor**, **thermal monitor** and **voltage to see which part of the abnormal issue, and then resolved.

BIOS is the master Steward of the computer environment before the computer operating system is started, so it is important to keep the BIOS. Can look at: