The most experienced hard disk Repair Tool pc3000 can reset the smart status!

Pay attention to the risks of this software. Do not try it for cainiao !!!!
V14 and V12 modified the following bugs. Unfortunately, they still do not support SATA and SAS hard disks?
1. Non-Russian. Optional. English.
2. More than GB hard disk recognition is added.
3. provide hard disk repair speed.

I. Introduction to pc3000
PC-3000 is a commercial professional hard drive repair integrated tool developed by Ace laboratory, a famous Russian hard drive laboratory. It manages the hard disk from the internal software of the hard disk, and changes and repairs the original data of the hard disk. You can perform the following operations:
1 servo scan 2 Physical scan 3 LBA address Scan
4 shielded factory channels (p-list) 5 shielded head
6. Block track 7. Block Bad Sectors 8. Change BIOS (parameter)
9. Change LBA size 10 to Sn
11. View or modify the negative header information
Ii. main use of pc3000
Hardware and software integrated tools "PC-3000" is mainly used to repair a variety of models of IDE Hard Drive, capacity from 20 mb to 200 GB, supported hard drive manufacturers are: Seagate (Seagate ), western Digital, Fujitsu, quantum, Samsung, maxtor, Conner, IBM, HP, kalok, teac, daeyoung, and xebec.
Using strongswan-3000 may repair hard disks with defects of 50-80%. Such a high repair rate is achieved through the use of a special hard disk working mode (such as the factory mode). In a special working mode, you can perform the following operations on the hard disk:
Low-level internal formatting;
Overwrite the hard disk's internal microcode module (firmware );
Rewrite the hard disk parameter identifier;
Check the defective sector or track, and reset, replace, or skip the defect;
Re-adjust internal parameters;
Indicates the head with a logical disconnection (that is, disallow) defect;
S. m.a. R. T parameter reset ....
Specifically, the firmware module has a special effect on data recovery in some situations, such: after power-on, maxtor, golden diamond, and Star Diamond hard drives, they cannot be correctly identified (no head noise). After power-on, the Fujitsu MPG and MPF hard drives are basically normal, but cannot be correctly detected; the IBM tenglong series has a head seek sound (no noise), but cannot be correctly identified. The quantum hard disk can be detected but cannot be read or written. The wd eb and BB series hard disks can be detected, but cannot read and write ...... the faults listed above are generally not hardware faults. Through PC-3000 operations, most similar faults can be solved, and most of the data
Still intact.
III. Basic principles of pc3000
Crack the instruction set of dedicated hard disk CPUs of various types, interpret firmware (firmware) of various hard disks, so as to control the internal work of the hard disk, and implement read/write of the internal parameter module of the hard disk and call of the hard disk program module, in the end, the software can repair multiple hard drive defects.
The most professional features are: re-write the firmware module of the hard disk, scan the internal defects of the hard disk in the factory mode, and record the corresponding parameter modules in the hard disk; perform internal low-level formatting in the factory mode; and change the hard disk parameters.
After more than ten years of research, Ace laboratory has been able to support most of the new and old models of IDE interface hard drives with a capacity of 40 MB to 200 GB.

Pc3000v12 Installation Method
1. Edit config. sys.
Device = C:/himem. sys (required)
Device = C:/pc3000/emulator/emm386.exe path editing by actual path
DOS = high, umb
Buffers = 60
Files = 45
2. Batch Processing vgaga or garbled code
3. Run pcdosemu space 2 (the hard disk to be repaired is on the second ide port)
4. execute shell
Note: The emm386.exe file uses the Russian version,
English translation of pc3k
Contents
PC-3000 complex 3
PC-3000 integrated tools
1.1. Purpose 3
Purpose
1.2. PC-3000 software, version 10.10 3
PC-3000 software, release 10.10
1.3. PC-3000 complex suite, version 10.10 5
1.4. Warranty 5
Authorization
1.5. Users Registration
User Registration
1.6. Registered PC-3000 users support 6
PC-3000 registered user support
1.7. PC-3000 complex installation 6
Installation of PC-3000 integrated tools
2. Universal Tester for diagnostics and repair of HDD of any type 8
Hard Disk models that can be diagnosed and repaired by the universal Tester
2.1. Purpose 8
Purpose
2.2. Preparation for work 8
Preparations
2.3. information output during work with PC-3000AT 8
Information output when the PC-3000AT is working
2.4. parameter input for the HDD being tested 9
Input parameters of the hard disk to be tested
2.5. PC-3000AT operation modes 9
PC-3000AT Operation Mode
2.5.1. Operation Mode Selection 9
Operation Mode Selection
2.5.2. Viewing S. m.a. R. T. Parameters of the drive 10
View Drive S. M. A. R. T. Parameters
2.5.3. Drive Test 11
Drive Test
2.5.4. Controller Test 13
Controller Test
2.5.5. complex test 16
Comprehensive Test
2.5.5.1. HDD tests making up the "complex test" 18
Composition of Hard Disk "Comprehensive test"
2.5.6. Defects relocation 19
Defect Reset
2.5.6.1. Automatic Relocation 19
Auto reset
2.5.6.2. Manual relocation 20
Manual reset
2.5.6.3. Relocation undo 20
Cancel Reset
2.5.7. Formatting 20
Format
2. PC-3000 shell 22
Pc3000 shell program
4. PC-DEFECTOSCOPE ver. 2.10 23
4.1. purpose 23
Purpose
4.2. Preparation for work 23
Preparations
4.3. Work with PC-defectoscope 23
Work of PC-defectoscope
4.4. rabbitming tests 24
Test
4.5. PC-defectoscope use for HDD repair 25
PC-defectoscope for hard drive repair
4.6. exported defects file structure 25
Format of the defect output file
5. Western Digital "caviar" arh.4 "PC-A313000" "PC-A310100" "PC-A38400" "PC-A36400" 27
Number of West "caviar" arh.4 "PC-A313000" "PC-A310100" "PC-A38400" "PC-A36400"
5.1. Purpose 27
Purpose
5.2. Basic options for WD caviar arh.4 drives repair 27
Basic repair options for the West "WD caviar arh.4" Drive
5.3. Preparing for Work 27
Preparations
5.4. Using the utilities 28
Valid program used
5.4.1. Servo Test 28
Servo Test
5.4.2. Surface Test. 28
Surface Testing
5.4.3. Disk firmware Zone 29
Disk firmware Area
5.4.4. Drive description Area 31
Drive description area (ID)
5.4.5. Formatting 31
Format
5.4.6. Logical scanning 31
Logic Scan
5.4.7. S. m.a. R. T. Table 32
S. M. A. R. T. Table
5.4.8. Defects Table 32
Defect table
5.4.9. automatic mode 33
Automatic Mode
5.5. brief technical description of WDC ac313000, WDC ac310100, WDC ac38400 and WDC ac36400 drive families 34
Brief technical description of the WDC ac313000, WDC ac310100, WDC ac38400, and WDC ac36400 series drivers
5.5.1. Disk firmware data 34
Disk firmware data
5.5.2. Initialization 35
Initialization
5.5.3. Changing drive's configuration 35
Change hard disk settings
5.6. Drive restoration algorithm 42
Hard Disk Recovery rules
5.7. Drive restoration in automatic mode 43
Recover the drive in automatic mode
5.8. Creation of disk firmware database 44
Create a firmware Database
6. Western Digital "caviar" arh.3 "PC-A35100" PC-A34000 "45
Western Digital "caviar" arh.3 "PC-A35100" PC-A34000"
6.1. Purpose 45
Purpose
6.2. Basic options for WD caviar arh.3 drives repair 45
Basic options for West WD caviar arh.3 drive repair
6.3. Preparing for Work 45
Preparations
6.4. Using the utilities 45
Valid program used
6.4.1. Servo Test 46
Servo Test
6.4.2. Surface Test 46
Surface Testing
6.4.3. Disk firmware zone 47
Disk firmware Area
6.4.4. Drive description area 49
Drive description area (ID)
6.4.5. Formatting 49
Format
6.4.6. Logical scanning 49
Logic Scan
6.4.7. S. m.a. R. T. Table 50
S. M. A. R. T. Table
6.4.8. Defects Table 50
Defect table
6.4.9. automatic mode 51
Automatic Mode
6.5. brief technical description of WDC ac35100 and WDC ac34000 drive families 51
Brief technical description of the West digital WDC ac35100 and WDC ac34000 series drivers
6.5.1. Disk firmware data information 53
Disk firmware data information
6.5.2. Initialization 54
Initialization
6.5.3. Changing drive's configuration 54
Change drive settings
6.5.4. peculiarities of hardware changing of the configuration 54
Change hardware settings
6.5.5. Magnetic Heads switching 55
Head Switch
6.5.5.1. Heads switching examples 58
Head switch example
6.6. Drive restoration algorithm 59
Drive recovery rules
6.7. Drive restoration in automatic mode 60
Recover the drive in automatic mode
6.8. Creating a disk firmware database 61
Create a firmware Database

PC-3000 Complex
PC-3000 integrated tools
1.1. Purpose
Purpose
The hardware and software complex "PC-3000" version 10.10 is designed for diagnostics and repair of any HDD with IDE interface of all modifications (ATA, ATA-2, ATA-3, ATA-4, ultraata, E-IDE, udma66) and advanced factory mode repairs and restoration of widely used hdds: Conner, daeyoung, Fujitsu, Hitachi, IBM, kalok, maxtor, NEC, quantum, Samsung, Seagate, teac, Western Digital, xebec, with the help of specialized shortical utilities (see utilities list ).
PC-3000 10.10 Is for diagnostics and maintenance (ATA, ATA-2, ATA-3, ATA-4, ultraata, E-IDE, udma66) hardware and Software Integrated for advanced manufacturer-level maintenance and recovery of hard disks with many ide interfaces. It is widely used to help professional HDD's: Conner, daeyoung, Fujitsu, Hitachi, IBM, kalok, maxtor, NEC, quantum, Samsung, Seagate, teac, Western Digital, xebec, etc.
1.2. PC-3000 software, version 10.10
PC-3000 software, version 10.10
Universal Software
General Software
PC-3000 SHELLPC-3000 shell graphical user interface for PC-3000 complex for fast and convenient start of utilities. Convenient PC-3000 integrated graphics start using Module Interface
PC-3000AT ver. 4.05 universal Tester for diagnostics and repair of HDD of any type. General Inspection Programs for Diagnosis and Maintenance of multiple hard drives
PC-DEFECTOSCOPE ver 2.10 universal program for search and hiding of unstable and bad sectors. Common Programs for searching and hiding unstable and Bad Sectors
PC-ACIDENT identification utility for Western Digital hdds of the AC family. West digital wdac series authentication Device
Invalid ical utilities
Technical components
.
.
.
2.5.5. Complex Test
2.5.5 Comprehensive Test
Complex test-test mode for input/output type control of the drive.
Comprehensive Test-Hard Disk input/output type control test mode
The following tests are sequentially stored med during complex testing:
Perform the test in the following sequence during the test:
-Controller Test
-Controller Test
-IRQ Test
-IRQ Test
-Sector buffer Test
-Slice buffer Test
-Recalibration Test
-Repeat the test
-Format check;
-Format check
-Random reading;
-Random read
-Surface scanning.
-Surface scan
The testing information appears on the tester display, in the status line and the State Register and error register led-S. The status line contains:
The test information is displayed in the status bar and status latches, and the test information is displayed in the error latches. The status bar includes:
Ready/busy-determines the drive status using the BSY bit of the State Register;
Prepare/busy-BSY bit indicating that the disk is in use status.
Done-the current test execution duration in % (appears when long tests are saved med)
Done-Percentage of execution duration of the current test (displayed during long test)
Cyl-current (active) Cylinder value;
Cyl-current (active) Cluster Value
Head-current (active) Head value;
Head-current (active) Head Value
Errs-current number of drive errors detected during each test.
Errs-number of errors detected by the current Hard Disk
"LBA mode" the current LBA sector is displayed in the state line in LBA mode instead of the CYL and head parameters.
"LBA mode" the current LBA sector is displayed in the status bar, replacing cyl and head Parameters
The tests are selected from the main "testing mode selection" menu, with the following message appearing on the tester display:
Test is selected from "test mode selection" on the main menu. The following information is displayed:
Attention!
Note:
Testing will destroy your data
Testing will destroy your data
Start cylinder: x
Start cluster: x
End cylinder: *** x
End cluster: *** x
Do write test: Yes
Write test: Yes
Press [enter] or [cancel]
Press ENTER or cancel 』
By default the starting and ending test cylinders correspond to the zero and the maximum HDD cylinders.
The default start and end clusters correspond to 0 and the maximum HDD clusters.
"LBA mode" you have to enter the starting and ending LBA sectors for testing in LBA mode. by default the starting and ending test LBA sectors correspond to the zero and the maximum LBA sectors of the drive.
LBA mode-you must enter the start and end LBA sectors. The default start and end clusters correspond to 0 and the maximum hdd lba sectors.
Attention! Note that the user data kept on HDD will be destroyed by the last test "surface scanning ". user data will be damaged by the last "surface scan" test in order to cancel writing in the "surface scanning" test highlight the "Do write test" line and press the "N" key. otherwise, to turn on writing in the "surface scanning" test highlight the "Do write test" line and press the "Y" key. press "n" in the "Do write test" option bar to cancel writing in "surface test. Otherwise, press "Y" in the "Do write test" option bar to open the write test.
As the testing procedures from the "complex test" go on, the evaluation of their results-pass or fail-appears on the tester display near the name of each test. the mark "running" appears near the name of the test, which is executed at the moment. the complex test can be interrupted by pressing the [enter], [cancel] or [exit] keys, which bring the "operator interrupt" menu on-screen. the menu allows you:
As the test starts from the comprehensive test, the results obtained in the test-pass or fail-are displayed near the names of each test, the "run" mark is displayed near the test name at the moment of execution of the test. You can press enter, cancel, and exit to interrupt the overall test. The operation interrupt menu appears on the screen.