Three topologies and transformer calculation of switching power supply

Source: Internet
Author: User

Switching power supply Three topologies: Buck,boost,buck-boost. The topology diagram is as follows:

Buck

Boostδ

Buck-boost

Transformer calculation:

One, Buck circuit transformer calculation

The buck Circuit is the most severe inductor operating condition at the highest input voltage;

1, first set the following parameters: Input voltage vin, Output voltage iout, operating frequency F;

2, because the circuit works in the critical mode, so the inductor peak current of 2Iout;

3, duty ratio d=vout/vin;

4, by the Volt-second balance v*ton=l*i, can get L= (V*DT)/di = (V*DT)/ipk, of which ton=d*t=d/f;

5, determine the number of primary winding turns: n1= (l*di)/(Δb*ae) = (L*IPK)/(ΔB*AE);

6, determine the number of secondary winding turns: n2= (VCC*N1)/(Vin-vout).

Second, flyback transformer calculation

Buck-boost circuit, the lowest voltage is the worst case

If the circuit is in CCM mode, take frequency to F .

Note: 1, NP is the primary winding turn number, NS is the secondary winding turns;

2, VMOs for MOS maximum withstand voltage, 1 for rectifier tube pressure drop, Vl for leakage, Vl=100v,vmos selection follows the principle: switch off the moment, add on the MoS voltage value of VMOs 25% (or 30V), should leave a 50V margin.

1. Determine the primary/secondary turns ratio

∵vmos=vinmax+ (vo+1) +VL

∴ primary/secondary turns ratio n=np/ns= (vmos-vinmax-80-100)/(vo+1);

2, ensure the core is not saturated and always work in CCM mode

By the Volt-second balance (Vinmin-1) ton= (vo+1) *toff---① (set MOS, Rectifier is the forward-guide voltage drop of 1V)

To ensure that the circuit works in DCM mode, the ton+toff=t should be-----------②

So ①② tonmax={(vo+1) * (np/ns) *t}/{(Vinmin-1) + (vo+1) * (Np/ns)};

3, primary inductance determination

∵pout= pin,pout=vo*icps* (toff/t), pin=vinmin*icpr* (tonmax/t);

(ICPR: Primary current rise ramp middle value, Icps: secondary current descent ramp median)

∴icpr= (po*t)/(Η*vinmin*tonmax)

∵icpr=dip/2

∴lp= = (Vinmin-1) *tonmax/dip= (Vinmin-1) *tonmax/(2*ICPR)

4. Initial/secondary turns determined

np= (LP*IP)/(Δb*ae)

ns=np/n

5, initial/secondary current RMS value determination

Irms (Beginner) = (ip/√3) * (√ (ton/t))

Irms (secondary) =ip* (np/ns) * (√ (toff/t))/(√3)

If the circuit is in CDM mode,

(not to be continued)

Three topologies and transformer calculation of switching power supply

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.