TP-Link TD-W89841N Enhanced Wireless Router Quick Setting Guide

TD-W89841N enhanced quick Setup Guide

Preface

TD-W89841N as the latest support 11N technology of wireless ADSL Router, it is a set of routers, switches, wireless AP, firewall in one, can support ADSL (telephone line), LAN (network cable home) Two access methods, you can select an appropriate access method based on your actual situation. TD-W89841N has three working modes:WirelessADSLRouting,WirelessADSLBridge,Wireless Routing, This article will introduce the most common working modes-WirelessADSLRouting Mode.

 

I.PCNetwork parameter settings

1. manually set network parameters:

(1) network parameter settings in Windows XP

1. Manually specify an IP Address: if you are using a Windows 2000/XP operating system, right-click "Network neighbors" on the desktop and choose "properties ", then select the local connection corresponding to the network card connecting to the ADSL Modem ". Right-click the "local connection"-"properties ".

Select Internet Protocol (TCP/IP) in "general" and click Properties.

Select and use the following IP address. In the red box above, enter IP Address: 192.168.1.2, subnet mask: 255.255.255.0, Default Gateway: 192.168.1.1, and enter the DNS server address in the red box below, if you are not sure, contact your local carrier. After setting, click OK.

 

1. Dynamic acquisition of IP Address: Let the host automatically get the IP address, DHCP server of the TD-W89841N is enabled by default, can automatically assign an IP address to the host, such.

Select "automatically obtain IP Address" or "automatically obtain DNS address". However, if the carrier already provides a DNS address, you are advised to enter it manually. Click "OK" after setting it.

 

(2) network parameter settings in Windows 7

1. manually set network parameters

Right-click "network"-"properties" on the desktop ".

Click local connection ".

Click "properties ".

Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.

Select and use the following IP address. In the red box above, enter IP Address: 192.168.1.2, subnet mask: 255.255.255.0, Default Gateway: 192.168.1.1, and enter the DNS server address in the red box below, if you are not sure, contact your local carrier. After setting, click OK. The setting is complete.

 

2. Dynamically Retrieve IP addresses:

Let the host automatically get the IP address, the DHCP server of the TD-W89841N is turned on by default, You can automatically assign an IP address to the host, such.

Select "automatically obtain IP Address" or "automatically obtain DNS address". If the carrier already provides a DNS address, you are advised to enter it manually. Then, click "OK.

 

II,TD-W89841NParameter settings

Set the network parameters on the pc and enter them in the browser.Http: // 192.168.1.1Open the WEB management interface of the device. Enter the User name: admin, password: admin, and click OK to go to the management main interface.

Note: If the management page cannot be opened or the default user name and password cannot be accessed, manually reset the route. RESET method: Press and hold the RESET key for 5 seconds in the live state, and the SYS light flashes three times, indicating that the route has been restored to the factory settings.

 

Click "setting wizard" in the left-side menu bar of the management interface ".

Click Next.

Select a wireless ADSL route and click Next.

In this interface, enter the Internet account and password provided by the network operator (such as China Telecom or China Netcom) when you apply for the ADSL Broadband Service. Make sure that the input is correct and click Next.

Wireless status: If the router features wireless, you must enable it so that hosts in the wireless network can access and access the wired network.

SSID number: The Network Name of the wireless network.

Channel: select the frequency band (1-13) for the wireless network ).

Mode: select the working mode of the router, optional 802.11b mode with 11 mbps bandwidth, 802.11g mode with 54M bandwidth, M 802.11n mode, 802.11b/g mode and 802.11b/g/n mode.

Bandwidth: automatic, 20 MHz, and 40 MHz.

Maximum sending rate: default value.

Wireless encryption: to prevent unauthorized access to your wireless network, we recommend that you set wireless encryption to WPA-PSK/WPA2-PSK.

After setting, click "Next ".

In this way, you have completed the basic network parameter settings required for accessing the Internet, click restart, the system will automatically restart, and then enter the management interface, you can view the WAN port status in "running status. If the WAN port status shows that the IP address, subnet mask, gateway, and DNS server address have been obtained, the router has been connected to the Internet.

Now, you can access the Internet through the vro.

This article is from the "Network worker experience sharing" blog