Truly solve the problem of connecting ActiveSync to wince5

I am a mini2440 board. I had a one-day connection problem between ActiveSync and wince5 yesterday. I searched all major forums and posted a help post in the csdn wince section, I did not expect to solve the problem as follows:

Http://hi.csdn.net/link.php? Url = http://topic.csdn.net %2fu%2f20100105%2f20%2f5326df67-4476-4816-9415-07bc4bd9d11d.html

Note that you must use the dm9000 Nic for connection and set it to DHCP to obtain the IP address. Note that the DNS server must be set to your computer's DNS so that resolution can be performed.

At the beginning of the installation, I was confused because I didn't understand it. As a result, I had trouble. Later I unloaded the installation and loaded the installation. Some people say that the DHCP service is not enabled, but I check that my DHCP is on, so I don't care about it. Let him connect himself. When I connect, I first establish a synchronization relationship, I think it is okay to create a file. If you connect to the file after it is created, you can connect to the file without interrupting file transfer. However, there is a red exclamation point on the icon in the lower right corner. If you do not establish a cooperation relationship, it will prompt you when the final connection is established: You can copy and move information between mobile devices and computers, but cannot synchronize the information. I think it doesn't matter. The most important thing is that there is no red exclamation mark on the icon in the lower right corner. This looks more comfortable!

To help more beginners understand, I will record the main steps:

1. Restart your chcp Service (it is better to be secure. I am on, but I still cannot connect to it). This is very important.

2. Disable the host NIC (I saw in the help of ActiveSync that I disabled the NIC of the PC once, but I found that the NIC can be connected even if it was not disabled. So this step can be omitted)

3. Click Start> Settings> network and dial-up connections on the Development Board and double-click dm9ce1. Set it to automatically get the IP address, and the DNS service is set to the same as your computer. (Important)

4. Click Start of the Development Board-> Settings-> control panel, double-click PC connection, and click: Change connection. Make sure you use the USB method (important)

The hardware has been set. The following describes the actual connection steps.

5. Enable ActiveSync first.

6. next, start the development board. After wince5 is started, insert the USB into the computer. If you have installed ActiveSync and inserted it for the first time, you must set it with caution and install the driver, this is what I eat. If the USB is inserted multiple times, ActiveSync may not automatically connect.

7. Then open the main panel of ActiveSync. If no response is displayed after the USB is inserted, click File, select connection settings, and click Connect in the upper right corner.

8. software prompt: to connect this device to the next PC, please plug in the cable or something, you can click next, and then the software is looking for COM port or something, and finally prompts that no device is detected. Don't worry about it. Click Cancel. After you click Cancel, the Development Board will automatically connect to your computer. The icon in the lower right corner is green ~! In the connection settings, the mobile device is connected.

9. Then the software will prompt you to establish a connection and cooperation relationship for file synchronization. As mentioned above, you can establish cooperation or not. I didn't establish a cooperation relationship, because after the establishment, the software will change the content to be searched, and the most prompt will be you: no configuration relationship is created, you need to create a configuration file, click the mail icon on the control panel. I used office2007. I don't know how to configure it. If you know something, let's talk about it. This is the red exclamation point on the icon ActiveSync in the lower-right corner.

However, you can upload files and Debug Programs whether or not you have established a cooperation relationship.

If no cooperation relationship is established, the connection ends. Files can be transferred, programs can be debugged, but files cannot be synchronized. We do not need to synchronize files ~

 

Communication: krcc@msn.cn

QQ: 790386196

By krcc_rain

 

Reprinted please indicate the source