Update the router installation specification

The router installation specification has been updated a lot. This article cannot copy the entire specification. This is just a hot update. I hope you will learn more about the configuration of wireless routers.

Wireless Router installation instructions

First, change the IP address of the local network adapter or wireless network adapter on your computer to an automatically obtained IP address. Generally, the specified IP address and other information are relatively stable, I used a fixed IP address for instructions. A friend who is familiar with the IP address can manually specify the IP address. The 45 After IP address 192.168.2.45 can be any one between 2 and. however, you cannot use the same IP address or duplicate IP addresses.) use only one Nic and disable all other NICs.) connect your Nic to any of the LAN ports of the router, after connecting.

Double-click the network adapter and click "support" to check if the gateway is 192.168.2.1. If the computer is connected to the vro, go to the vro installation manual and set it. After the connection is established, open IE, which is the address bar of the website. Enter 192.168.2.1 to go to the router settings page, we can see that there is an Internet WAN main menu on the left, and then we can see the sub-menu connection Type in it. At this time, we will come up with a Login option no matter what we click, asking us to enter the password, click the submit key below.

Go to the settings project. Here is where we need to set the key points. In the above field, 9023 only shows four numbers. Some port numbers may be 5-digit, for example, 15572, don't worry about this. You can set 15572. The number 15572 is random. You can replace the number 15572 based on your own port number. In this case, many streaming media software require open ports. After the settings are complete, the downloaded page will be displayed remotely during BT.

Security is the encryption option in the main menu of Wireless. After you click it, select the Encryption Class in Security Mode, generally, if you select 64bit WEP, you can enter the 10-digit password in KEY 1 and click Apply Changes. after encryption, wireless encryption will be prompted. When you click Connect, you need to enter the password. Just enter the password and OK.

The instruction manual is constantly being improved. This instruction is sent to all users. If you have any questions, please give me more advice. I hope you will carry forward the spirit of Lei Feng and make the electronic instruction manual more comprehensive. Send it to me! Thank you again! Use the MAC address filtering function to ensure the security of your wireless network.

There are multiple encryption methods in the wireless router installation instructions, such as WEP encryption and MAC address filtering. However, due to the technical problems of WEP, the use of WEP encryption will lead to unstable usage and slow speed. Based on our experience, the MAC address filtering method is the most stable and reliable. Now we will introduce how to use this encryption method.

First, assume that you have a laptop, a desktop, and a desktop without the need to consider encryption. This is mainly because the laptop is wireless. (ALL the descriptions below are for wireless NICs) let's take a look at the MAC address of your laptop wireless network card. Maybe someone will ask what you think? Now, let me first talk about how to view the MAC address of your wireless network adapter. In the lower left corner of the desktop, click Start-run, Enter CMD, and enter ipconfig/all in the command line.

Next, follow the router installation instructions to enter the router management interface, enter the MAC address of your wireless network card into the address box, that is, step 3, and click ADD (ADD ), click APPLY (SAVE ). OK. It takes effect after the computer is restarted. After this setting, no wireless network adapter except the wireless network adapter with the MAC address specified here will be able to use this router, even if it can receive your signal, but cannot be connected. Do not believe it.

Note:

Block: indicates that the network is restricted for NICs with the following MAC addresses. If this parameter is not checked, the network is allowed. Generally, you only need to leave the check box blank and enter the MAC address of your network card. This way, even if someone else's wireless network card can receive your signal, it will always be unable to connect and play an encrypted role. One is Dynamic (suitable for users who have automatically assigned IP addresses in the LAN, and also for vro connected users. When the vro is connected to the vro, note that the IP addresses of the two vrouters are not the same, that is, the two IP addresses that enter the settings page cannot be the same. For example, the IP address of the wireless router LAN of SMC is 192.168.2.1.

If the router installation specification is connected to the back of smc, it will not work. You must change the IP address of any of them to 192.168.1.1 instead of using a network segment. Haha, don't ask me how to change it, this is very simple. There is a LAN Settings in the Settings, and 192.168.2.1 is the gateway, the address modification of the gateway is like this. You can change 192.168.2.1 as long as the first 2 is changed to 1, it can also be changed to a number, as long as the 2 is not in any number between 0-2 50) click Apply Changes .).

The second is static point NEXT (suitable for network users with specified IP addresses, many of which are designated IP addresses in the LAN, and most of the school network is designated IP addresses, if you are a friend of the specified Internet, first copy the IP information on your local Nic or wireless network card on the paper and then change it to automatically get the IP address, because the IP address you specified cannot access my vro installation instructions, pay attention to this. After this option is selected, replace your IP subnet mask, enter the number of the Gateway DNS to the corresponding location. The IP Address is IP subnet Mask and the subnet Mask is the ISP Gateway Address.

Apply Changes. After DNS is enabled in the Internet wan, remove the IC from ISP check box and then fill in the check box, you can see the status of the vro: internet settings has an internet IP address. the wan ip address is the Internet IP address. please note that there is a difference on the top of BT01 BT02. in TYPE, one is TCP, and the other is UDP. You must take a look. the port on BT is shown as follows: Click the option in the option on the top of the btsoftware, and a listening port is displayed.

For other functions and settings, you have to find relevant information. For BT, you need to set vitual servrs In Firewall: for example, if the IP address used on my computer is 192.168.2.45, and the port of BT is 9023, click Apply Changes .) OK! The third is PPPOE (this is suitable for most household users. We use PPPOE for ADSL. This is also the case if the LAN in some residential areas has a user name and password, click NEXT and enter your broadband User name and password in the User name field on another page. Enter the Retype Password and click Apply Changes again) after these settings are complete, check whether the settings are complete and check the upper right corner of the settings page. click Home.