Use a USB flash drive to create a Windows 7 installation disk and MacBookAir for Win7

Use a USB flash drive to create a Windows 7 installation disk and MacBookAir to install Windows 7-general Linux technology-Linux technology and application information. The following is a detailed description. This method uses a USB flash drive to create a Windows installation disk. It is applicable to the installation of a USB flash drive on any machine, but not limited to a Mac machine. The second half describes windows installation on Mac.

First, you need to prepare a Windows 7 computer with an optical drive. In addition, you need to prepare a Windows 7 system disc and a USB flash drive of at least 4 GB (not available for flash memory + card readers ), it takes about one hour to prepare again. Well, that's enough.

1. Detailed steps for installing Windows 7 on a USB flash drive

1. Insert the USB flash drive to Windows 7 and start the CMD command prompt as an administrator.
(Click Start-type "CMD" in the search area-right-click CMD and choose "Run as administrator)

2. Open Diskpart. This is because the system we usually see is a letter drive, and we need to change it to the original number.
(Enter "diskpart" in CMD, press enter, switch to DISKPART>, enter "list disk", and press Enter)

3. now the screen should show all the storage devices in use on the computer. According to the capacity, we can see which one is the USB flash drive we inserted, and 3856 MB is of course a 4 gb usb flash drive, let's select it (enter "select disk 3" in CMD, where the USB flash disk is located)


(400) {this. resized = true; this. width = 400; this. alt = 'click here to open new window';} "onmouseover =" if (this. resized) this. style. cursor = 'hand'; "onclick =" window. open ('HTTP: // img.evolife.cn/2010-10/55eebffca1cdfe6c_thumb.jpg'); ">

There is no mistake in each of the subsequent steps. In addition, you must make sure that you have successfully selected the USB flash disk location in step 1, otherwise, other hard disk data will be cleared.
(Enter "clean" in CMD to clear the USB flash drive, enter "create partition primary" to create the primary partition, and enter "select partition 1" to select partition 1, enter "active" to mark the selected partition as an active partition, enter "format fs = ntfs" to format partition 1 of the USB flash drive, and enter "assign" to assign a drive letter to the selected partition, enter "exit" to exit Diskpart. (when "assign" is entered, the USB flash drive may be disconnected and reconnected. This is normal. Please do not panic)


(400) {this. resized = true; this. width = 400; this. alt = 'click here to open new window';} "onmouseover =" if (this. resized) this. style. cursor = 'hand'; "onclick =" window. open ('HTTP: // img.evolife.cn/2010-10/a2dde6f7bb452961.jpg'); ">

4. we need to install Windows 7 content into the USB flash drive. Please insert your Windows 7 CD into the optical drive (in this case, the drive is located in the drive E, and the drive is located in the H, please replace the applicable drive letter automatically)
Tip: After the disc is inserted, assume that your drive letter is "E:" "cd boot" is "e:" "cd boot" in CMD. Input "“bootsect.exe/nt60 h:" To enable boot and install it to the USB flash drive, then copy all the files on the CD to the USB flash drive. ~~~~


(400) {this. resized = true; this. width = 400; this. alt = 'click here to open new window';} "onmouseover =" if (this. resized) this. style. cursor = 'hand'; "onclick =" window. open ('HTTP: // img.evolife.cn/2010-10/2df7de6fdd429792_thumb.jpg'); ">


5. next, copy all the installation content of the Windows 7 CD to the USB flash drive. It takes about 10 minutes to install Windows 7 on any computer after that, however, you must set the USB flash drive in BIOS as the preferred one. Okay, after the USB flash disk is installed, Let's take out the USB flash disk and take out the new MacBook Air that has been waiting for a long time.


2. Install Windows 7 on MacBook Air

>>>> Read the full text