Use LTSP to create ?? No hard disk Workstation

Use LTSP to create ?? No hard disk workstation-Linux Enterprise Application-Linux server application information. The following is a detailed description. First, I ?? Required? By ?? This system? ? Station bottom? Some ??, At least the following kits must be included:

Ltsp_core-3.0.5-0.i386.rpm-LTSP Kit
Ltsp_kernel-3.0.4-0.i386.rpm? ?? Linux core
Ltsp_xcore-3.0.1-1.i386.rpm? Workstation X-Windows (for kernel 4x)
If you want to use very old? ?? Persons ??? Why? C required? Go down? Some? X-Windows 3.3.6? Makes me ??? Yes? What is the display card? To? Good results.

Why does workstation support sound effects ?? Required kits? Ltsp_sound-3.0.1.i386.tgz. Me ?? Persons ?? Why ?? Gray? Option ^ use sound effects, because? Why ?? Poor W Road ???.

? Yes, me ?? At? Required Before LTSP? First? Good DHCP, tftp-server, and nfs-utils.

? In? Me ??? Start frame? LTSP !!
Install rpm-ihv ltsp_kernel-3.0.4-0.i386.rpm ltsp_core-3.0.5-0.i386.rpm ltsp_xcore-3.0.1-1.i386.rpm first
Then run: ltspadmin will display
Ltspadmin-v0.17 LTSP dir:/opt/ltsp-4.2

LTSP Administration Utility

Install/Update LTSP Packages
Configure the installer options
Configure LTSP

Quit the administration program
After you see this, you can configure
Step 1: Configure the installer options ENTER
LTSP Installer configuration
If the configuration file
Where to retrieve packages from?
[Http: // 10.0.2.htm/STUDY/LTSP/ltspins/]
Step 2: Install/Update LTSP Packages
The following configuration file is displayed:
Ltspadmin-v0.17 LTSP dir:/opt/ltsp-4.2

Retrieving list of packages from http: // 10.0.2.htm/STUDY/LTSP/ltspins /...
500 Can't connect to 10.0.2.0000: 80 (connect: No route to host)
Status: 500 Can't connect to 10.0.2.0000: 80 (connect: No route to host)
Unable to retrieve list of packages!

Press To return to main menu
Step 3:
Configure LTSP ENTER
The following words appear.
Ltspcfg-Version 0.16

Checking Runlevel...: 5
Checking Ethernet Interfaces
Checking Dhcpd .....
Checking Tftpd .......
Checking Portmapper...
Checking nfs.../etc/host. conf: line 1: expected service, found 'zhanggencai, bind'

Checking xdmcp...
Checking/etc/hosts.
Checking/etc/hosts. allow.
Checking/etc/exports.
Checking lts. conf.

Press To continue ..
Then press ENTER
Ltspcfg v0.16 The Linux Terminal Server Project (http://www.LTSP.org)
S-Show the status of all services
C-Configure the services manually

Q-Quit

Make a selection:
Step 4: Configure by C.
Ltspcfg v0.16 The Linux Terminal Server Project (http://www.LTSP.org)
1-Runlevel
2-Interface selection
3-DHCP configuration
4-TFTP configuration
5-Portmapper configuration
6-NFS configuration
7-XDMCP configuration
8-Create/etc/hosts entries
9-Create/etc/hosts. allow entries
10-Create/etc/exports entries
11-Create lts. conf file

R-Return to previous menu
Q-Quit

Make a selection:
Note: 7 select "no" for the second (yes/NO ).
Step 5: You can view the Service Startup and configuration by S.
Ltspcfg v0.16 The Linux Terminal Server Project (http://www.LTSP.org)
Interface IP Address Netmask Network Broadcast Used
Eth0 10.0.2.176 255.255.255.0 10.0.2.0 10.0.2.255 <-----
Vmnet1 172.16.168.1 255.255.255.0 172.16.168.0 172.16.168.255
Vmnet8 192.168.72.1 255.255.255.0 192.168.72.0 192.168.72.255

Service Installed Enabled Running Notes
Dhcpd Yes Version 3
Tftpd Yes Has '-S' flag
Portmapper Yes
Nfs Yes
Xdmcp Yes xdm, TPD, kdm Using:

File Configured Notes
/Etc/hosts Yes
/Etc/hosts. allow Yes
/Etc/exports no
/Opt/ltsp-4.2/i386/etc/lts. conf Yes

Configured runlevel: 5 (value of initdefault in/etc/inittab)
Current runlevel: 5 (output of the 'runlevel' command)

Installation dir...:/opt/ltsp-4.2

Press To return to the main menu...
Finally, start some unstarted files.
This is done!