Use PS Channel to replace the exterior beauty with small fresh light green effect

Original

< small map view big picture >

Final effect

1, the first need to the picture in the warm and cold tones evenly, more cool colors need to increase the warm. Warm colors require more cool colors. The color of the material picture is less warm. Open the material picture, create an optional color adjustment layer, yellow, green adjustment, parameter settings such as Figure 1, 2, the effect is shown in Figure 3.

< map 1>

< map 2>

< map 3>

2, create an optional color adjustment layer, the yellow adjustment, parameters and effects of the following figure. To this step the cool and warm colors in the picture are moderately proportional.

< map 4>

3, create a new layer, press CTRL + ALT + Shift + E-stamped layer, as shown below.

< map 6>

4, enter the channel panel, choose the Green channel, press CTRL + A Select all, press CTRL + C copy. Select the blue channel, press CTRL + V paste, and then point to the RGB channel back to the layers panel, the effect is shown in Figure 8. Above we adjust the picture the effect of the warm and cold in Figure 8 is very obvious.

< map 7>

5, create optional color adjustment layer, red, green adjustment, parameter settings such as Figure 9,10, the effect is shown in Figure 11. This step mainly turns the cyan in the picture into green.

< map 9>

< map 10>

< map 11>

6, create curve adjustment layer, RGB, red, green, blue to adjust, parameter settings such as Figure 12-15, the effect is shown in Figure 16. This step is to lighten the color of the picture.

< map 12>

< map 13>

< map 14>

< map 15>

7, the creation of optional color adjustment layer, yellow, green, white adjustment, parameter settings such as Figure 17-19, the effect is shown in Figure 20. This step mainly to the picture in the green light.

< map 17>

< map 18>

< map 19>

< map 20>

8, create color balance adjustment layer, shadow, midtones, high light adjustment, parameter settings such as Figure 21-23, the effect is as Figure 24. This step is to fine-tune the color of the dark part and the high light portion of the picture.

< map 21>

< map 22>

< map 23>

9, press CTRL + ALT + 2 to pull up the high light selection, create a new layer fill light green: #E7EFE0, the opacity to: 20%, the effect of the following figure. This step softens the color of the picture.

< map 25>

10, create an optional color adjustment layer, red, yellow, white to adjust, parameter settings such as Figure 26-28, the effect is shown in Figure 29. This step adds red to the picture, and the high light portion increases the light cyan.

< map 26>

< map 27>

< map 28>

< map 29>

11, a new layer, stamped layer. Execution: Filters > Blur > Gaussian blur, the value is 5, OK after holding down the ALT key to add layer mask, with a white brush to the background need to wipe out the blur, the effect of the following figure.

< map 30>

12, a new layer, stamped layer. Execution: Filter > Blur > Motion blur, Angle set to 45 degrees, distance set to 150, after the change layer blending mode to "soft light", the opacity to: 30%, the effect of the following figure.

< map 31>

13, create a color balance adjustment layer, the midtones, highlight adjustment, parameter settings such as Figure 32,33, the effect is shown in Figure 34. This step softens the color of the picture.

< map 32>

< map 33>

14, the use of Lasso tool to select the face of the characters, the appropriate feather after the creation of curve adjustment layer, the face slightly brighter skin, the effect of the following figure.

< map 35>

15, create a new layer fill light green: #C6E5C0, blending mode to "filter", opacity to: 50%, press and hold down the ALT key to add a layer mask, with a white brush to the upper left corner of the section, the effect of the following figure.

< map 36>

16, create a new layer, with the elliptical marquee tool pull out the oval selection shown in the following figure, feather 20 pixels after the fill light red: #C7866F, blending mode to "filter", the opacity to: 50%, the effect of the following figure.

< map 37>

17, create optional color adjustment layer, to red, yellow to adjust, parameter settings such as Figure 38,39, the effect is shown in Figure 40. This step is to fine-tune the character's complexion.

< map 38>

< map 39>

< map 40>

Finally, fine-tune the color to complete the final effect.