Use PS to shine a dark yellow photo to rub skin beauty

The following photos to be processed, the original image is dark, and yellow. The face of the character has shiny, difficult to deal with, need some patience. The process is mainly two steps, one is a simple color palette, and then the character of the skin, as well as the partial liquefaction finally modified some of the details, the completion of the effect.

Effect comparison:

The steps are as follows:

1, open the original picture. First, we'll color the pictures.

2, set up a color level adjustment layer, adjust the whole.

3, create a brightness contrast adjustment layer, adjust the brightness, and contrast. A slight adjustment can be, the effect is not very obvious, but I still adjusted a bit.

4, create a curve adjustment layer, the blue channel to lighten up a little, red channel slightly illuminated. In the RGB channel, the upper right corner is raised a little lower left corner.

After the curve is adjusted, the effect is now as follows:

5, set up a brightness contrast adjustment layer again, to add some brightness to the whole.

6, create an optional color adjustment layer, adjust the red:

7, the overall color to adjust here almost. Now use the high contrast to keep the character to make a simple rub skin.

Press Ctrl+shift+alt+e to merge all the layers first. Then change the layer mode to overlay:

Then reverse-phase the layer 1. Ctrl+i reversed phase. After the reverse phase, use high contrast to retain the filter, the size of the filter radius adjustment, attention to observe the character skin. This step is to make the skin a little more delicate. The size of the radius is very critical, too large, too fake skin, too small, to achieve the effect of grinding skin.

After the filter completes, add a full black layer mask to layer 1. After you select Layer 1, hold down the ALT key and then click the Add Vector mask button

, it's OK.

After the mask is added, use the eraser, rub the skin part of the character, pay attention to the part of the eyes and lips, keep sharp, do not need to grind the skin. When using the eraser, note that the foreground color is set to black and the background color is white.

8, after the simple grinding process, it is necessary to grind the skin carefully. Because of the quality of the original skin is not good, it is not enough to rely on high contrast reservation alone.

First Use the "Repair Tool" to the character face of some patches, and so on, roughly deal with:

9, then, use the "stamp tool" to deal with the shiny face, pay attention to the eyebrows of the place, not to deal with too false on it. Then we have to deal with the details again. Shine on the nose of the time, pay attention to the nose of the high light part, do not have a little high light. That way, the nose is a bad sight.

10, continue to use the stamp tool, the skin to do a further meticulous treatment.

11, now, the skin of the face is almost the same, now we deal with the five senses, first of all the lip part. Now the lip edge is a little blurred, with your favorite tool, the edge of the lip to deal with it, I use the Stamp tool, this time the stamp, hardness of 80, opacity of 40.

After processing the effect is as follows:

12, now adjust the color of your lips, and first draw a lip line to your lips. I used a brush tool, a little bit smaller, and a slightly darker color than my current lip, drawing along the edge of my lip.

Brushes: pattern is overlay, opacity is 15%, stroke size is 5

13, use the Lasso tool, first select the tooth selection, and then use the hue saturation tool, adjust the yellow, the teeth white point:

When using a selection tool, such as a lasso, a pen, etc., select the approximate area of the lip section and then use the optional color to adjust the red and yellow:

The lip color effect is as follows:

14, use the Stamp tool or other tool to handle the left corner of the mouth, and other teeth also processing:

15, now to adjust the color of eye shadow. Here I did not adjust too much, just let the original color more vivid. Press Q to enter the quick mask, and then use the 0 hardness of the brush, the eye shadow area wipe out, and then press Q to exit the quick mask. Then reverse the selection: Ctrl+shift+i

16, after the selection, adjust the optional color, this time to adjust the red, so that the original eye shadow, a bright color. Don't get too rich.

17, press Ctrl+shift+alt+e to merge the layers, and then use the liquefaction filter to decorate the character's chin, nose, and lips:

Before:

After liquefaction:

18, using the Stamp tool, the lip is processed, and now the lip is a little rough.

19, then, the ears and neck of the skin, also with a seal to deal with. These places, a little treatment, not too rough on the good:

20, and then to adjust the eyes, the main eye adjustment is to the whites of the part, to lighten up a little, deflexion with the stamp tool slightly modified, need to pay attention to is not the whites of white made.

21, up to now. Overall, the wipe is not much, but found that in the background, incredibly personal So this picture looks very uncomfortable, now take back the characters in the well.

You can use any tool you like when you go to a background character. I like the stamp tool better. There is no need to do too meticulous, as long as the background can not see a person on the line, because the background is now very vague. The effect of removing:

22, to see if there are any details that need to be dealt with? eyebrows there ~ ~ Not very comfortable to look at:

The effect after processing again:

23, finally using a topaz filter, the image processing a little bit more fine. Look more beautiful. The filter processing step does not say, the Topaz filter may download from this station.

The final effect is as follows:

Note : More wonderful tutorials Please pay attention to the triple Photoshop tutorial section, triple PS group: 75789345 welcome you to join

Category:

• PS Image Processing
• PS Grinding Course