Using Linux BT5 to crack wireless hack wireless

The following is the specific steps of their own, copyright small von All.

First, prepare the BT5 ISO image file in advance. and virtual machines, install the virtual machine in advance, and then install the BT5.

Second, enter the page, click Statx, enter the visual interface.

Third, after entering the main interface, download the reaver-1.3.tar.gz file. and copy this file to the root directory.

Four, open the terminal, enter the command tar–zxvf/reaver-1.3.tar.gz (actually to perform the file decompression)

Enter the main file →reaver folder →src, and then in the menu bar above, click Tools to open the terminal.

Vi. Enter the command./configure

VII. Enter command make

Eight, enter the command make install

Nine, on the virtual machine, the wireless network card, loaded into the virtual machine.

Ten, in the main interface, open the terminal, Airmon-ng start wlan0

Xi. input Command Airodump-ng mono

12. Input command reaver–i mono–b hack Wireless MAC address –a–s (uppercase) –w–d 0-VV

The complete steps are as follows:

First, download the tools you want to use:

1. System: bt5r1-gnome-32,http://pan.baidu.com/s/1b1d6o

2. Software: Reaver-1.3.tcz,:http://pan.baidu.com/s/1nctov

or software: REAVER-1.4-SVN-R107.TCZ,:HTTP://PAN.BAIDU.COM/S/1TBYTJ

3, U disk burning tool: slightly

4.

Second, the production of U disk Startup disk, the process slightly

Three, now the system cmd, and then Ipconfig/all, find your wireless network card MAC address, this will find it? Do not write down, remember the wireless and Wired MAC address, can differentiate on the line, two put together to find that is wireless on the line, Then put Reaver-1.3.tcz or REAVER-1.4-SVN-R107.TCZ into the computer's hard drive or another USB flash drive, set the computer boot sequence to start the USB stick, plug the USB stick to start the computer.

Four

1, after the start of the first choice of the interface, (if the start more than 4 minutes throw did not enter into the interface to force the restart and try again, if not, tell me, it may be this version does not support U disk startup or your USB disk boot disk did not make good, the problem of production) Select default First, enter, 3.1

Figure 3.1

2, wait a moment, into the figure 3.2 interface, enter StartX, enter the BT5 system (English version)

Figure 3.2

3. Click on the bottom right corner of the screen 3.3 red circled that, pop-up figure 3.3 that window, the left to find you save Reaver-1.3.tcz, copy, and then close the window (third x on the top left of the window), paste on the desktop, copy and paste a reaver-1.3.tcz on the line, 1.4 that the temporary no tube, the result 3.4

Figure 3.3

Figure 3.4

4, open the terminal, figure 3.5 red circle up that, input

tar-xzvf/root/desktop.reaver-1.3.tar.gz Input and Results

Figure 3.5

5. Close the window, reopen the terminal, enter

Cd/root/reaver-1.3/src

Then enter, and then type./configure

Inputs and results such as 3.6

Figure 3.6

6, etc 5 after the completion of the stop input

Make

3.7

Figure 3.7

7, continue to wait for the completion of the execution after the stop input make install

3.8

Figure 3.8

8. Close these windows when you are finished executing. Re-open a terminal, enter Reaver, 3.9 is the installation is successful, otherwise reinstall, 4-7 steps, or restart the computer to reinstall ( there are two points of note: 1, after the restart all data is emptied, 2, Shutdown click on the terminal next to the system inside the shutdown, can not shut down press the switch machine 5 seconds Force shutdown)

Figure 3.9

9, the software after the installation began to crack work, the first step, re-open a terminal, open before, other windows can be turned off, in the terminal input ifconfig-a, (not ipconfig AH) in the following appear inside Find Wlan0, Wlan1 what and the back of the MAC address, remember that your wireless is Wi-Fi a few, do not remember the cable on the line, figure 3.10

Figure 3.10

10, continue to enter Airmon-ng start Wlan0, here Wlan0 is you above the WLAN a few is the WLAN a few, enter the following 3.11, appear in the diagram 3.12 underneath the circle is successful, 3.11 Under the circle is wrong, because the bottom of the ring up the above hint Unknow error 132, I made a mistake so cut 2 pictures, and then re-Plug and change the next, restart the next, generally come out the default result is Mon0 is not mon1,

Figure 3.11

Figure 3.12

, 11, then the input airodump-ng mon0, you the last step to re-mon a few is a few, enter 3.13

Figure 3.13

12, enter after the scanning of the vicinity of the wireless network, 3.14, those parameters of the specific what to look at Figure 3.14 to go, there is 54e. The ability to crack, that point not to leak

Figure 3.14

13, wait 10 seconds later, press CTRL + C is suspended, find a signal good, 54e. Of the crack,-1 signal the best,-90 the worst, the signal (-70)-(-90) directly can not be considered, you can also try, anyway, no impact, figure 3.15

Figure 3.15

14, this window is not closed, and then open a terminal, input reaver-i mon0-b to crack the wireless MAC address-a-s-vv-d 0, pay attention to the case, note the space, to crack the wireless MAC address can be from the previous window right-click Copy paste come over, 3.16, figure 3.17 is already starting to crack.

Continuous occurrence of different values is the normal crack, occasionally appear one or two times the same does not matter.

Figure 3.16

Figure 3.17

15, the general pin is clear when the longest ten hours The shortest 1 seconds can be cracked out of the password but the more the pin is slower, the fastest like that 1seconds/attempt,1s a pin, Normal is 3-4 seconds 1PIN, slow time can be 90 seconds 1pin is possible.

If the same number appears for a long time, as shown in Figure 3.18, so congratulations, you put someone else routing pin dead, he did not affect the Internet, you can no longer hack his route, only wait for him to restart the route or after the power of his home after you can continue to crack, (I will tell you I have a way to attack other people routing so that he can not be forced to restart the network Route, although BT5 originally is to integrate a bunch of hacking tools, but this black people routing method I do not go out, please eat a meal may be transmitted)

You use your wireless network card to crack out before the probability of a pin dead others routing is very large, the time to crack do not expect to be able to crack out, that is not too realistic, a couple of days is likely to crack, the pin died for that, the pin died and then change, the next day maybe pin dead that route restarted, PIN, Then the previous progress, below the method to save the progress.

Figure 3.18

16, save the crack progress method,

Using Linux BT5 to crack wireless hack wireless