Using Photoshop to add a dream light green blue Tutorial to a bamboo wedding slice

Original

< small map view big picture >

Final effect

1, open the material picture, press CTRL + J to copy the background layer, into the channel panel, select the green channel, press CTRL + A, press CTRL + C copy, select the blue channel, press CTRL + V paste. Point RGB channel Return to the layer panel, the effect of the following figure. This step gets a more pure cyan picture.

< map 1>

2, create hue/saturation adjustment layer, adjust the cyan, parameter settings such as Figure 2, the effect is shown in Figure 3. This step turns the cyan in the picture into a lighter blue color.

< map 2>

3, create curve adjustment layer, RGB, green, blue adjustment, parameter settings such as Figure 4-6, the effect is shown in Figure 7. This step is mainly to brighten the dark part of the picture, and to add blue to the picture.

< map 4>

< map 5>

< map 6>

< map 7>

4, create an optional color adjustment layer, green, blue, white adjustment, parameter settings such as Figure 8-10, the effect is shown in Figure 11. This step mainly to the picture in the green tone light.

< map 8>

< map 9>

< map 10>

5, press CTRL + J to copy the current optional color adjustment layer, the opacity to: 30%, the effect of the following figure.

< map 12>

6, create optional color adjustment layer, red, black to adjust, parameter settings such as Figure 13,14, the effect is as shown in Figure 15. This step appropriately reduces the red in the picture and tunes the dark color.

< map 13>

< map 14>

7, the layer at the bottom of the layers to copy a layer, press CTRL + Shift +] top, and then hold down the ALT key to add a layer mask, with a white brush to the face and arm parts of the figure, as shown below.

< map 16>

8, create hue/saturation adjustment layer, first tick the "coloring" option, and then set parameters, such as Figure 17. When you are sure, press CTRL + ALT + G to create the clipping mask, and then change the layer opacity to: 80%, the effect is shown in Figure 18.

< map 17>

< map 18>

9, create an optional color adjustment layer, the red, white, neutral color adjustment, parameter settings such as Figure 19-21, determined to press CTRL + ALT + G to create a clipping mask, the effect is as shown in Figure 22.

< map 19>

< map 20>

< map 21>

10, create brightness/Contrast adjustment layer, the appropriate increase in picture contrast, parameter settings such as Figure 23, determine the same press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 24. These three steps adjust the character's complexion.

< map 23>

< map 24>

11, create a new layer, press CTRL + ALT + Shift + E-stamped layer, press CTRL + SHIFT + U to color, blending mode to "multiply", and opacity to: 30%. Then hold down the ALT key to add a layer mask, with a white brush to the bottom need to deepen the part of the wipe out, the effect of the following figure.

< map 25>

12, a new layer, stamped layer, execution: filter > Blur > Dynamic blur, Angle set to 45 degrees, distance set to 180, to determine the layer blending mode to "soft light", add layer mask, with a black brush to the bottom of the transition to wipe out, the following figure.

13, press CTRL + J to copy the current layer layer, the opacity to: 30%, the effect of the following figure.

< map 27>

14, create curve adjustment layer, the picture dark part slightly darkened a bit, parameters and effect of the following figure.

< map 28>

< map 29>

15, create a new layer, fill blue: #8EA8B8, blending mode to "filter", hold down the ALT key to add a layer mask, with a white brush to the upper right corner of the section, the following figure.

< map 30>

16, a new layer, stamped layer. Simple to rub the skin of the characters, using fuzzy tools to the background part of the need for fuzzy processing, the effect of the following figure.

< map 31>

Finally, fine-tune the color to complete the final effect.