What is the reason for moving the mouse pointer to a standstill?

What is the reason for moving the mouse pointer to a standstill?

Usually, the mouse pause is the sensitivity of the mouse is poor, the sensitivity of the optical mouse is a common fault, the specific performance of the mouse when moving, the cursor unresponsive, do not listen to command. This hardware troubleshooting advice is to change a new mouse immediately.

However, it is best to pass the following troubleshooting reasons to verify that the mouse pauses in the end where the problem!

First, make sure your mouse is good. You can switch to another computer and try it. Test whether the mouse socket can not contact the cause.

Second, reload the driver for the video card or sound card.

Third, anti-virus.

Four, software conflicts.

The hard disk file fragment, when the hard disk file fragmentation too much, will lead to serious system operation delay

Six, check your motherboard CMOS on the motherboard bus frequency, memory refresh frequency settings, to see if the wrong set of parameters, when the memory operating frequency and the motherboard can not sync, will automatically insert the waiting period waiting for the motherboard to provide the appropriate next clock pulse, so memory work will slow!

VII, hard disk magnetic medium aging. Hard disk for a long time, the magnetic medium will gradually aging, then read and write latency than the new hard disk will be many times slower, general use of full format or low-level format can solve the problem, but you need to back up all data files.

First, click "System-Hardware-Device Manager" from the control Panel, locate "USB ROOT HUB" under the Universal Serial Bus controller, double-click, then open the "Power Management" tab, Cancel "yes", allow the computer to turn off this device to save power selection, OK, exit. What's up? The mouse will no longer malfunction!

If not, this is likely to be a mouse delay, it is recommended to first kill a computer virus, the mouse is slow to indicate that the system is slow, or you are controlled by others, you find the mouse delay when you open the Task Manager to see the CPU consumption, if very large, is the system has problems or is controlled, If the CPU usage is normal may be your mouse hardware problem!

Knowledge expansion reading:

Why is there no reason to break the screen and a mouse pause

One, clean up the disk and defragment the disk

1. In My Computer window, right-click the drive letter you want to clean-"properties"-"clean disk"-tick the file you want to delete-ok-yes.

2. Clear temporary files, start-run-enter%temp%--OK.

3. Clean up the registry and junk files with the Master or Super Bunny.

4, defragment disk--start--All Programs--accessories--System Tools--Disk Defragmenter--Select c--analysis--defragmentation.

Second, optimize the computer with the optimization master or the Super Rabbit.

Third, optimize the BIOS settings.

1, into the BIOS to change the default settings to optimize settings.

After you turn on your computer or restart your computer, press the "Del" key to enter the BIOS setup screen and find the load Oprimum SETTINGS (load the motherboard BIOS factory settings) in the Open interface, which is the factory BIOS optimizer.

There is a load high performance DEFAULTS (higher performance default), which is used to load BIOS optimization settings.

Press ESC after selecting the optimized value with the keyboard arrow keys, press f10,y, enter, or select Save&exit Setup (save and exit Settings), press Y, enter, save the changed settings and exit the BIOS setup.

2. Close the floppy drive.

Reboot, press del into BIOS to locate BIOS FEATURES Setup, select, enter to open BIOS FEATURES Setup interface, turn D rive A: 1.44m 3.5in behind, change to None (off), press ESC to return to main interface, save exit.

3. Turn off the floppy drive detection function.

Start the computer, press the DEL key to enter the BIOS setup main interface, find the advanced BIOS Features (high-level BIOS parameter settings) press ENTER, in the interface, "boot up floppy Seek (boot Floppy detection)" set to "Disabled", Press ESC to return to the main interface and save the exit.

4. Open the Quick Start self-test function

Start the computer, press the DEL key, enter the BIOS setup main screen, select "Advanced BIOS Feat