Wind 10-Pack Centos7

Work relatively leisurely, free to have nothing to do nature to find fun, by the way to upgrade their computer technology, the earliest WIN10 installation centos7 thinking is such, before listening to the old Peaches can install the system, The CentOS. ISO is placed in the LMT file directory, the BIOS boot interface for a installation, for me this small white, sounds very good and simple, but the fact is not satisfactory, to install the interface after the installation, in the detection process can not read the USB flash drive or the installation source bar, so in the process has been looking for a U disk (installation source) SDA, SDB, SDC have tried again or not, even let me doubt to life, later changed a train of thought, for our small white should be better, do not have to install the old peaches, directly mirror all write to the U disk, so it should not be wrong, there is a lot of information on the Internet, But for the old Peaches install Centos7 failed to now still brooding, hope there can be resolved to communicate with each other, learn from each other, the following is a U disk write Mirror win10 machine after installation CENTOS7 process

First, the ISO image is completely written to the USB stick, be sure to write (here do not use the old Peaches tml installation)
Second, start the flash drive, in the CentOS interface press the TAB key to change the parameters (if no changes will appear to read the USB flash drive results, reported errors until #模式下面)
1. Determine the identity of the USB stick
VMLINU2 initrd=initrd.img linux dd quiet
Start, according to the name of the USB stick (windowns under the tool to write a disk when generally known as the ISO name of the disk, such as the CENTOS7 system, after writing should be centos7.xxx, presumably this way, when the start can be seen, a glance will know) to find a USB stick logo, such as SDC4
2, modify the Mount location information will be inst.stage2=hd:/after the information all erased, changed to
VMLINU2 initrd=initrd.img INST.STAGE2=HD:/DEV/SDC4 Quiet
SDC4 is what we find the U disk identifier (according to their actual situation, some may also be SDA, SDB beginning, see the 1th Step)
3, this time can be smoothly into the installation interface, after choosing their favorite type can be, here simple directly omitted

经过一番努力之后我们终于可以进入到LINUX下，但还有一个问题来了，那就是安装完毕后，我们开机启动项下，我们只看到centos 7启动项，分别是正常启动和centos7修复启动，这里并没有win10启动项，所以需要在修改centos7中参数

4 Modifying the startup item (refer to the Gatherfly Weibo link address: 51864247) Other verification methods can draw on its fifth step of Weibo
Vi/boot/grub2/grub.cfg or Vim/boot/grub2/grub.cfg find a place to write, generally in the last write can, convenient
Menuentry ' Window 10 ' {
Insmod Chain
Insmod Chain
Set root= ' HD0,MSDOS1 '
Chainloader +1
}
Then: Wq Finish saving
Main parameters hd0, the representative is the disk identification, installation of Windows disk, is also the first hard disk, we usually 0 for the first block, and so on, MSDOS1 represents the first disk, that is, the C disk, we usually windows the first disk for the C drive, the conventional system is installed to the C drive, Of course there are many pieces of hard drive plug different interface, here according to their own situation, do not write wrong, otherwise will error,
Tips: Find hard disk Convenient method, will not be wrong, that is to use PE, into the disk Management, will find hard disk letter is HD a few, after confirmation if again fault the start item written wrong, carefully check again

After modifying the parameters generally can start normally, after restarting will appear three startup options, of course, WIN10 is inside, you can use the

Wind 10-Pack Centos7