Ying Tai motherboard set U-Start Program

The first step: when the computer is in the shutdown state, will already use U start to make a good Startup disk U disk plug into the computer host USB jack (in order to be able to well identify the U disk, we recommend that you insert the U disk into the mainframe box after the USB socket, and then turn on the computer, when the splash screen when we press the "Del" button continuously ( Del key position: in the bottom right corner of your keyboard, the penultimate position will appear, the interface of the BIOS setup of the Yingxiu motherboard, as shown below:

The second step: press the left and right direction key ←→, move the cursor to the "Advanced" place, and then press up and DOWN ARROW keys ↑↓ the cursor movement selected to the "SATA Configuration", the following figure:

The third step: when the choice to SATA configuration, we press the ENTER key, will appear another interface, that is, change the hard disk mode of the Setup interface, as for why to set the hard disk mode? because the U boot PE system may not recognize the AHCI mode hard drive because there is no associated drive, So what we're going to do is change the hard drive mode to IDE mode first. We are now moving the up and down arrow ↑↓ to move the cursor to the "SATA mode Selection", which we can see behind the default mode: [AHCI] is shown below:

Fourth step: When you select to "SATA mode Selection", we press ENTER, we will pop up a small window for our choice, namely "IDE" and "AHCI", press the UP and DOWN ARROW keys ↑↓ Select to the IDE, and then press ENTER. The following figure:

By the way, the meaning and relationship of the two:

Both "IDE" and "AHCI" are hard disk interface technologies.

AHCI mode: Support for Intel hard disk caching technology, SATA hard drive generally recommended. The disk will read faster when turned on. In particular, the reading of some fragment data can be added quickly. If not, there are some features of SATA drives that are not up to the extreme. XP under the open after the effect is not very obvious. But the Win7 has a remarkable effect.

IDE: SATA driver support is not required. is obviously an old interface way. But the mission that history has entrusted to it has been fulfilled. Not much to say here.

If the hard drive supports AHCI recommendation open. The installation system requires SATA drive after it is turned on. We can install it by driving the life, driving the wizard or the OEM website.

Fifth step: Set the hard disk mode for the IDE, we next set the USB boot mode, press the "ESC" key to return to the "Advanced" option, and then locate and press the arrow keys to move the cursor to the "USB configguration" option, and then press ENTER, as shown below:

Sixth step: Press ENTER to enter another interface, at this time, we continue to press up and down direction key ↑↓ will move the cursor selection to "Generic Flash Disk 5.00", the following default option is [Auto], we want to change this option, so we press ENTER, the following figure:

The seventh step: when presses the ENTER key to pop up a selection window, inside the choice has: "Auto", "floppy", "forced FDD", "Hard Disk", "CD-ROM". At this point we select the "Hard Disk" option, and then press ENTER to confirm. The following figure:

Eighth step: All the above settings are completed, we will now set the BIOS first boot for the U disk to start! Press ESC to go back to the BIOS setup main interface, and then press the left and RIGHT arrow keys to move the cursor to the "BOOT" option, and then press the UP and DOWN ARROW keys to move the cursor to the Hard Drive BBS Priorities option, and then press ENTER to enter another setup interface, as shown in the following figure:

Nineth step: Next to go to another setup interface, we choose the default first "Boot Option #1", and then press ENTER, pop-up a selection of small windows, the options are: "Generic Flash Disk 5.00", "PO:WDC Wd5000avds-61u7b1 "," Generic Flash disk 5.00 "," Disabled ", no matter how many options, we choose the first Generic Flash disk 5.00 and then press ENTER, do not have to understand what they mean. The following figure:

The tenth step: the above operation as long as we have finished after the set U disk startup has been completed, now we only have to save the above settings. We press "F4" key, and then will pop up a dialog window, indicating whether to save the meaning of the exit, we can directly press ENTER to determine, and then the computer will automatically restart, after the reboot can be launched from the U disk. The following figure:

If you think the above is too complicated, then you start small set to teach you a most direct method, that is, the use of shortcut keys directly into the U disk start: Press F9 button can choose U disk start directly into!

        Note : more Wonderful tutorials please focus on the Triple computer Tutorials section, triple Computer office group: 189034526 Welcome to join