You cannot log on to the vro page on the web and solve the problem in terms of hardware and software volume!

Why can't I set the wireless router login settings? To make the wireless router work efficiently, we often need to set it correctly. However, when we try to log on to the WEB management page of the wireless router and set wireless Internet access parameters, we often encounter failures where wireless routes cannot be set for login. How can we solve this fault?
There are two main reasons for this phenomenon: one is that the hardware factors such as line connection or wireless router are faulty, and the other is that the parameters of the wireless router or IE browser are improperly set.
Hardware faults mainly include network connection cable disconnection, network connection connector looseness, abnormal computer system operation, and damage to intermediate equipment such as hubs or routers, in this case, the failure can usually be determined by observing the wireless router signal lights. Of course, the input voltage is not normal, the internal temperature of the equipment is too high, or the equipment is struck by lightning, it is also prone to hardware faults.
When we observe the data signal lights in the wireless router control panel, if we find that the signal lights flash intermittently, it means the line connection is normal. Once we find that the signal lights are not working properly, check whether the connection of the broadband line is in reliable contact, and whether the internal core is in short or disconnected status. During this check, we can use other normal cables for testing.
After removing the cable, we need to go to the workstation to check the wireless network connection settings. For example, we can reset the IP address of the workstation Nic, if you find that you cannot log on to the wireless router when the IP address is automatically obtained, you can use a static IP address and disable the firewall used by the workstation system.
If the above troubleshooting method still does not work, we need to open the IE browser of the workstation system to check whether the connection settings of the program are correct. When performing this check, we can open the IE browser window and click the "Tools"/"Internet Options" command in the menu bar of the window, in the pop-up Internet option settings window, click the "connection" tab, select the "Never dial-up connections" item on the corresponding tab page, and click "OK.
Then, click the "LAN Settings" button, clear all the settings in the subsequent settings window, and then click the "OK" button, and try entering the wireless router address in IE browser to log on to the connection.
If the problem persists, the only thing we can do is to restore all the parameters of the wireless router to the default factory settings and reinstall the driver of the corresponding device, if this method does not work, we can almost conclude that the wireless router has a hardware fault. At this time, only professional technical personnel are invited to solve the problem.
Q: The problem that wireless routing cannot work stably is often caused by frequent disconnection when using a wireless router for broadband dial-up access. In addition to the network content we access, this phenomenon is also related to network virus attacks and parameter settings of wireless routers. To avoid this phenomenon, follow these steps to troubleshoot the problem one by one:
First, go to the background management interface of the wireless router and check whether the connection mode of the device is set correctly. Considering that common wireless routers often support more than three connection modes, by default, most wireless routers work in "On-Demand connection, automatically connect when there is access content. In other words, it regularly checks whether the dialing line is in the no-load status. If there is no data transmission interaction on the line after successful broadband dialing, the wireless router will automatically disconnect the current connection, so when we find that the wireless router works in the "On-Demand connection, automatic connection when there is access content" mode, you must log on to the wireless router backend settings window and select the "Automatic Connection, automatic connection after startup and disconnection" item in the connection method settings, finally, save the set parameters and restart the wireless router.
If the wireless router still cannot work stably after the above settings, it is necessary to check whether there is a network virus. During virus detection, we can use the latest version of anti-virus software to thoroughly scan and kill every "Corner" of the workstation system. After virus detection, you also need to enter the wks TCP/IP parameter settings interface, and try to use another IP address in this interface, so as to effectively avoid ARP network attacks. If the wireless router continues to fall offline, we need to use professional anti-attack programs to protect the wireless router.
Of course, if a wireless router is often dropped when we access a specific network content, most of the faults are caused by the Network content, in this case, we can try to access other network content to confirm whether the wireless router is abnormal.
Author: Xiaoyu home"