宏途_LCD調試流程.

今天在調試宏途的LCD屏時，開始是開機螢幕不亮，背光都不亮，可能板子已經損壞，一般通過測試電流電壓簡單驗證，(註：硬體引腳沒焊好也會引起讀lcd id出現錯誤！！！)出現這個問題一般是因為引腳沒焊好，可以找硬體幫忙；

 

焊接好後背光點亮，但是一直停在logo區，無法進入系統，如果logo顯示不正常，這個原因一般是u-boot讀不對lcd id導致載入kernel載入不了lcd驅動導致kernel死掉！；

U-Boot 2010.12-00001-gf3d69f8-dirty (Aug 222013 - 15:20:30)                           

                                                                            

DRAM: 256 MiB                                                              

NAND: The type of nand flash is 2KB page, so use default configuration!

512 MiB                                

MMC:  after set sd clk, CLK_GEN5:60000

mv_sdh: 0                              

Using default environment              

In:   serial

Out:  serial

Err:  serial

sci_efuse_calibration data:0

is_bat_low adc_value:784,comp_vbat:3500

mingwei ubootvol:3546,adc4200:928,adc3600:796

GEN0 1d382360

Bad block table found at page 262080,version 0x03

Bad block table found at page 262016,version 0x03

nand_read_bbt: Bad block at 0x00001f700000

nand_read_bbt: Bad block at 0x00001f780000

ANA_RTC_INT_RSTS is 0x820000b4

value of it 0x1

calibrate detecting

U-Boot 2010.12-00001-gf3d69f8-dirty (Aug 222013 - 15:20:30)

DRAM: 256 MiB

NAND: The type of nand flash is 2KB page, so use default configuration!

512 MiB

MMC:  after set sd clk, CLK_GEN5:60000

mv_sdh: 0

Using default environment

 In:   serial

Out:  serial

Err:  serial

sci_efuse_calibration data:0

is_bat_low adc_value:783,comp_vbat:3500

mingwei ubootvol:3541,adc4200:928,adc3600:796

GEN0 1d382360

Bad block table found at page 262080,version 0x03

Bad block table found at page 262016,version 0x03

nand_read_bbt: Bad block at 0x00001f700000

nand_read_bbt: Bad block at 0x00001f780000

ANA_RTC_INT_RSTS is 0x820000b4

value of it 0x0

calibrate detecting

 U-Boot 2010.12-00001-gf3d69f8-dirty (Aug 222013 - 15:20:30)

 DRAM: 256 MiB

NAND: The type of nand flash is 2KB page, so use default configuration!

512 MiB

MMC:  after set sd clk, CLK_GEN5:60000

mv_sdh: 0

Using default environment

 

In:   serial

Out:  serial

Err:  serial

sci_efuse_calibration data:0

is_bat_low adc_value:782,comp_vbat:3500

mingwei ubootvol:3537,adc4200:928,adc3600:796

GEN0 1d382360

Bad block table found at page 262080,version 0x03

Bad block table found at page 262016,version 0x03

nand_read_bbt: Bad block at 0x00001f700000

nand_read_bbt: Bad block at 0x00001f780000

test if there is a need to update spl......

yaffs: Mounting /backupfixnv

save exit: isCheckpointed 0

test if there is a need to updatefixnv......

yaffs: Mounting /backupfixnv

save exit: isCheckpointed 0

Reading fixnv to 0x00480000

yaffs: Mounting /fixnv

Copy /fixnv/fixnvchange.bin to0x00480000... st_size = 65540

[load_sector_to_memory]sync the latestfile......

save exit: isCheckpointed 0

yaffs: Mounting /productinfo

Copy /productinfo/productinfobkup.bin to0x00490000... st_size = 3076

[load_sector_to_memory]sync the latestfile......

save exit: isCheckpointed 0

SN1 = 18731502756478   SN2 =

DOWNLOAD : Pass; WRITESN : UnTested; CFT :UnTested; ANTENNA : UnTested; IMEI : UnTested; MobileTV : UnTested;

Last error: PASS

yaffs: Mounting /runtimenv

[load_sector_to_memory]both of the filesare not correct......

save exit: isCheckpointed 0

do_dcdc_work 60

adc chan 10, value 779

dcdc_calibrate default 1200mv, from 1174mvto 1230mv

dcdc_calibrate failure

[sc8810fb_probe]

[lcdc_mcu_init] LCDC_CTRL: 0x3

[lcdc_mcu_init] LCDC_BG_COLOR: 0xffffff

@fool2[lcdc_calc_lcm_timing] ahb_clk: 0xfa

@fool2[lcdc_calc_lcm_timing] ahb_clk: 0xfa

@fool2[lcdc_lcm_configure] LCM_CTRL: 0x4

@fool2[lcdc_update_lcm_timing]LCM_PARAMETER0: 0x7ff08df

nt35510_read_id 10

;……..;

Error: no valid bmp image at fa

yaffs: Mounting nothing all the file are not right!!! ???

yaffs: Mounting /productinfo

lcdid_buf = 0

Copy /productinfo/lcdid.file to0x0fc85ee8... st_size = 8

lcdid_buf1 =0

save exit: isCheckpointed 0

lcd_id 沒有匹配對

如果logo顯示正常，至少讀取lcd id是正確的，這個原因可能是系統記載到了不同平台的代碼，導致各種位移量出現錯誤，kernel無法正常運行，導致kernel死掉；

[    6.104000]df20: 00000000 00000200 cf15c000 c48fece4 cf0bd0e0 cf13bec0 00000000 cf13bf00

[   6.112000] df40: 000001dc 00000400 00000000 c46709c4 00000002 cf13bec000000002 cf13bec0

[   6.120000] df60: ffffffff c4671a3c cf150af0 c4a5a650 c4a5a690 c4557468 cf150ac0c4a5a650

[   6.128000] df80: cf15c000 cf15c000 cf15dfcc c48e7a28 00000000 c48e7e18cf027ee4 cf15c000

[   6.136000] dfa0: cf15dfd4 c4575e78 cf13bec0 cf15dfd4 c466f0c4 cf13bec000000000 00000000

[   6.144000] dfc0: 00000000 c466f104 cf027ed8 c4575e94 00000000 00000000cf15dfd8 cf15dfd8

[   6.152000] dfe0: 00000000 cf027ed8 c4575e18 c452ea18 00800013 c452ea1800000000 00000000

[   6.161000] [<c46a1fa0>] (zlib_deflateReset+0xe8/0x120) from[<c467db3c>] (deflate_compress+0x24/0x6c)

[   6.170000] [<c467db3c>] (deflate_compress+0x24/0x6c) from[<c4668cfc>] (crypto_compress+0x1c/0x24)

[   6.179000] [<c4668cfc>] (crypto_compress+0x1c/0x24) from[<c466f70c>] (test_comp+0x64/0x1f8)

[   6.187000] [<c466f70c>] (test_comp+0x64/0x1f8) from[<c46709c4>] (alg_test_comp+0x48/0x80)

[   6.196000] [<c46709c4>] (alg_test_comp+0x48/0x80) from[<c4671a3c>] (alg_test+0x7c/0x1c0)

[   6.204000] [<c4671a3c>] (alg_test+0x7c/0x1c0) from[<c466f104>] (cryptomgr_test+0x40/0x48)

[   6.212000] [<c466f104>] (cryptomgr_test+0x40/0x48) from[<c4575e94>] (kthread+0x7c/0x84)

[   6.220000] [<c4575e94>] (kthread+0x7c/0x84) from [<c452ea18>](kernel_thread_exit+0x0/0x8)

[   6.229000] Code: e5841070 e1a0c11c e5843060 e085200c (e19560bc)

[   6.235000] ##: Some locks are being holded.

 

或者是fmark未開啟,損壞，導致無法重新整理螢幕;

[  93.390000] init: sys_prop: permission denied uid:10012 gid:10012name:persist.msms.phone_default

[  93.436000] UMP<2>: New session opened

[  93.437000] Mali<2>: Session starting

[  93.450000] Mali<2>: Session has ended

[  93.450000] UMP<2>: Session closed

[  93.454000] init: sys_prop: permission denied uid:10012 gid:10012name:persist.msms.phone_default

[  93.493000] lcdc: sprd_lcdc_sync time out!!!!!

[  93.493000] sprdfb can not do pan_display !!!!

[  93.633000] lcdc: sprd_lcdc_sync time out!!!!!

[  93.633000] sprdfb can not do pan_display !!!!

[  93.783000] lcdc: sprd_lcdc_sync time out!!!!!

[  93.783000] sprdfb can not do pan_display !!!!

[  93.914000] lcdc: sprd_lcdc_sync time out!!!!!

[  93.914000] sprdfb can not do pan_display !!!!

[  94.022000] init: sys_prop: permission denied uid:10012 gid:10012name:persist.msms.phone_default

[  94.035000] init: sys_prop: permission denied uid:10012 gid:10012name:persist.msms.phone_default

[  94.043000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.043000] sprdfb can not do pan_display !!!!

[  94.085000] init: sys_prop: permission denied uid:10012 gid:10012name:persist.msms.phone_default

[  94.183000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.183000] sprdfb can not do pan_display !!!!

[  94.314000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.314000] sprdfb can not do pan_display !!!!

[  94.443000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.443000] sprdfb can not do pan_display !!!!

[  94.541000] logs4modem is waiting for /sdcard being mounted

[  94.583000] rtc alarm set at 1356998644, now 1356998525, rtc delta-28861.842999999

[  94.594000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.594000] sprdfb can not do pan_display !!!!

[  94.644000] logs4android is waiting for /sdcard being mounted

[  94.724000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.724000] sprdfb can not do pan_display !!!!

[  94.853000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.854000] sprdfb can not do pan_display !!!!

[  94.983000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.983000] sprdfb can not do pan_display !!!!

[  95.124000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.124000] sprdfb can not do pan_display !!!!

[  95.264000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.264000] sprdfb can not do pan_display !!!!

[  95.393000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.393000] sprdfb can not do pan_display !!!!

[  95.543000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.543000] sprdfb can not do pan_display !!!!

[  95.683000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.683000] sprdfb can not do pan_display !!!! [   94.594000] sprdfb can not do pan_display!!!!

[  94.644000] logs4android is waiting for /sdcard being mounted

[  94.724000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.724000] sprdfb can not do pan_display !!!!

[  94.853000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.854000] sprdfb can not do pan_display !!!!

[  94.983000] lcdc: sprd_lcdc_sync time out!!!!!

[  94.983000] sprdfb can not do pan_display !!!!

[  95.124000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.124000] sprdfb can not do pan_display !!!!

[  95.264000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.264000] sprdfb can not do pan_display !!!!

[  95.393000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.393000] sprdfb can not do pan_display !!!!

[  95.543000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.543000] sprdfb can not do pan_display !!!!

[  95.683000] lcdc: sprd_lcdc_sync time out!!!!!

[  95.683000] sprdfb can not do pan_display !!!!

0@C����

出現的是一直提示lcdc: sprd_lcdc_sync time out，發現是FMARK引腳並未開啟！

 

註：

1.      如果燒機後開機出現花屏且一直無法進入系統，可能的原因是下載了錯誤的工程軟體，或者是配置了錯誤的LCD配置！這個主要是參考主幹版本上lcd適配表，這個比分支上的lcd適配維護的更加完善！

2.      開機背光燈點亮，但是主屏不亮，這個原因一般就是沒讀對lcd 的id導致u-boot根本載入不了lcd的驅動，連開機的第一張圖片都載入不對，也就是showlogo出錯了，抓取分析u-boot的log,要麼就是lcd配置出現問題，要麼就是待適配的lcd id 本身就出現了錯誤，這個編譯驗證就可以解決！--z6_wvga_alx ,lcd ic:r68120,lcd moulde:CONFIG_COMB_LCD_MODULE_TYPE_WD43060AF_WVGA_R68120.

3.      Lcd幾個非常重要的寄存器需要格外注意，0x3500—TE_ON ;0x3600—MADCL;0x3A00—dataformat;0xBE—VCOM等等的寄存器，是調整lcd顯示效果必須注意的！