WinCE 6.0 KITL 正常使用 串口輸出資訊

[2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue Selection: 6 Enter Device
IP address (actual 0.0.0.0): 192.168.0.203 Device IP address set to 192.168.0.203-------------------------------------------------------------------------------- Network Settings--------------------------------------------------------------------------------
[1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue
Selection: 7 Enter Device IP mask (actual 0.0.0.0): 255.255.255.0 Device IP mask set to 255.255.255.0-------------------------------------------------------------------------------- Network Settings--------------------------------------------------------------------------------
[1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue
Selection: 0-------------------------------------------------------------------------------- Main Menu-------------------------------------------------------------------------------- [1] Show Current Settings [2] Select Boot Device [3] Select KITL (Debug)
Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 1 Main: Boot device: DM9000A MAC Debug device: DM9000A MAC Device ID: 0 Retail
Msgs: disabled SDCard: Filename: "nk.bin" Network: KITL state: enabled KITL type: active KITL mode: polled DHCP: disabled IP address: 192.168.0.203 IP mask: 255.255.255.0 IP router: 0.0.0.0 Eth MAC Addr: Invalid Ethernet chip ID (0xc000c00)!Controller not
found! VMINI: enabled Note: USBFN RNDIS MAC Addr cannot be changed.-------------------------------------------------------------------------------- Main Menu-------------------------------------------------------------------------------- [1] Show Current Settings
[2] Select Boot Device [3] Select KITL (Debug) Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 0DM9000DBG_Init: IndexPort = 0x15000000
, DataPort = 0x15000000DM9000 Mac Address: bc:37:e1:87:90:ffDM3730 Found DM9000 ID:90000a46DM9000 Chip Revison: 0x19DM9000 Work in 16 Bus WidthDM9000 Mac : bcDM9000 Mac : 37DM9000 Mac : e1DM9000 Mac : 87DM9000 Mac : 90DM9000 Mac : ffLink on ethernet at:100
MbpsDM9000_Init OK.INFO: Boot device uses MAC bc:37:e1:87:90:ffINFO: *** Device Name EVM3730-37119 ***+EbootSendBootmeAndWaitForTftpSent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent
BOOTME to 255.255.255.255Packet has the following data: boot.bin[NULL]octet[NULL]TFTP packet could have 1 name/value pairsLocked Down Link 1Src IP 192.168.0.203 Port 03D4 Dest IP 192.168.0.108 Port 0916Default TFTP block size set to: 512 bytesThere were no
options detected in the TFTPEthDown::TFTPD_OPEN::boot.bin-EbootSendBootmeAndWaitForTftpBL_IMAGE_TYPE_BINDownload file information:-----------------------------------------------------------[0]: Address=0x80101000 Length=0x0802a99c Save=0x80001000-----------------------------------------------------------Download
file type: 1TFTP: Desktop losing ACK, block number = 23211, Ack againTFTP: Desktop losing ACK, block number = 23211, Ack againTFTP: Desktop losing ACK, block number = 40339, Ack againrom_offset=0x0.ImageStart = 0x80101000, ImageLength = 0x802A99C, LaunchAddr
= 0x8010FDFCCompleted file(s):-------------------------------------------------------------------------------[0]: Address=0x80101000 Length=0x802A99C Name="" Target=RAMROMHDR at Address 80101044hGot EDBG_CMD_JUMPIMGGot EDBG_CMD_CONFIG, flags:0x00000000Launch
Windows CE image by jumping to 0x8000fdfc...Windows CE Kernel for ARM (Thumb Enabled) Built on Sep 14 2011 at 17:32:20ProcessorType=0c08 Revision=2 CpuId=0x413fc082OEMAddressTable = 8010fe9cOAL: CPU revision 0xffffffffOAL: CPU L2 Aux register 0x400042CPU CP15
Control Register = 0xc5387fCPU CP15 Auxiliary Control Register = 0x100e3--- High Performance Frequecy is 32768 khz---Changed KITL zone mask to 0x00008001DM9000DBG_Init: IndexPort = 0x15000000 , DataPort = 0x15000000DM9000 Mac Address: 8:38:e1:87:ff:90DM3730
Found DM9000 ID:90000a46DM9000 Chip Revison: 0x19DM9000 Work in 16 Bus WidthDM9000 Mac : 8DM9000 Mac : 38DM9000 Mac : e1DM9000 Mac : 87DM9000 Mac : ffDM9000 Mac : 90Link on ethernet at:100 MbpsDM9000_Init OK.WARN: KITL will run in polling modeVBridge:: built
on [Dec 30 2011] time [18:17:11]VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytesTx buffer [0xA8150F40] to [0xA8154F40].Rx buffer [0xA8154F60] to [0xA8158F60].VBridge:: NK add MAC: [8-38-E1-87-FF-90]Connecting to DesktopConnecting to Desktop .. resendingConnecting
to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting
to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingConnecting to Desktop .. resendingTexas Instruments Windows CE
SD X-Loader for EVM 3730Built Dec 31 2011 at 10:18:11Version 6.15.00open ebootsd.nb0 fileInit HW: controller RSTSDHC: 1 bit modeSDCARD: reqested speed 1000000, actual speed 1000000Using 4 bit modeSDHC: 4 bit modeSDCARD: reqested speed 25000000, actual speed
24000000read ebootsd.nb0 filejumping to ebootsd imageMicrosoft Windows CE Bootloader Common Library Version 1.4 Built Jul 14 2011 01:13:41Texas Instruments Windows CE EBOOT for Mistral OMAP EVM, Built Jul 14 2011 at 01:15:50EBOOT Version 1.1, BSP 6.15.00TI
DM3730 Version 0x2b89102f (unknown)TPS659XX Version 0x30 (Unknown)System ready!Preparing for download...INFO: Predownload....WARN: Boot config wasn't found, using defaultsINFO: SW4 boot setting: 0x2f>>> Forcing cold boot (non-persistent registry and other
data will be wiped) <<<Hit space to enter configuration menu 1...-------------------------------------------------------------------------------- Main Menu-------------------------------------------------------------------------------- [1] Show Current Settings
[2] Select Boot Device [3] Select KITL (Debug) Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 2--------------------------------------------------------------------------------
Select Boot Device-------------------------------------------------------------------------------- [1] DM9000A MAC [2] USBFn RNDIS [3] NK from SDCard FILE [0] Exit and Continue Selection (actual NK from SDCard FILE ): 1 Boot device set to DM9000A MAC--------------------------------------------------------------------------------
Main Menu-------------------------------------------------------------------------------- [1] Show Current Settings [2] Select Boot Device [3] Select KITL (Debug) Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash
Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 3-------------------------------------------------------------------------------- Select Debug Device--------------------------------------------------------------------------------
[1] USBFn RNDIS [2] DM9000A MAC [0] Exit and Continue Selection (actual (NULL)): 2 Debug device set to DM9000A MAC-------------------------------------------------------------------------------- Main Menu--------------------------------------------------------------------------------
[1] Show Current Settings [2] Select Boot Device [3] Select KITL (Debug) Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 4--------------------------------------------------------------------------------
Network Settings-------------------------------------------------------------------------------- [1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set
IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue Selection: 3 Set KITL to polled mode [y/-]: y KITL set to polled mode-------------------------------------------------------------------------------- Network
Settings-------------------------------------------------------------------------------- [1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask
[8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue Selection: 5 Disable DHCP (actually enabled) [y/-]: y DHCP disabled-------------------------------------------------------------------------------- Network Settings--------------------------------------------------------------------------------
[1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue
Selection: 6 Enter Device IP address (actual 0.0.0.0): 192.168.0.203 Device IP address set to 192.168.0.203-------------------------------------------------------------------------------- Network Settings--------------------------------------------------------------------------------
[1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue
Selection: 7 Enter Device IP mask (actual 0.0.0.0): 255.255.255.0 Device IP mask set to 255.255.255.0-------------------------------------------------------------------------------- Network Settings--------------------------------------------------------------------------------
[1] Show Current Settings [2] Enable/disable KITL [3] KITL interrupt/poll mode [4] KITL Active/Passive mode [5] Enable/disable DHCP [6] Set IP address [7] Set IP mask [8] Set default router [9] Enable/disable VMINI [a] Set MAC address [0] Exit and Continue
Selection: 0-------------------------------------------------------------------------------- Main Menu-------------------------------------------------------------------------------- [1] Show Current Settings [2] Select Boot Device [3] Select KITL (Debug)
Device [4] Network Settings [5] SDCard Settings [6] Set Device ID [7] Save Settings [8] Flash Management [9] Enable/Disable OAL Retail Messages [0] Exit and Continue Selection: 0DM9000DBG_Init: IndexPort = 0x15000000 , DataPort = 0x15000000DM9000 Mac Address:
bc:37:e1:87:90:ffDM3730 Found DM9000 ID:90000a46DM9000 Chip Revison: 0x19DM9000 Work in 16 Bus WidthDM9000 Mac : bcDM9000 Mac : 37DM9000 Mac : e1DM9000 Mac : 87DM9000 Mac : 90DM9000 Mac : ffLink on ethernet at:100 MbpsDM9000_Init OK.INFO: Boot device uses
MAC bc:37:e1:87:90:ffINFO: *** Device Name EVM3730-37119 ***+EbootSendBootmeAndWaitForTftpSent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Sent BOOTME to 255.255.255.255Packet has the following
data: boot.bin[NULL]octet[NULL]TFTP packet could have 1 name/value pairsLocked Down Link 1Src IP 192.168.0.203 Port 03D4 Dest IP 192.168.0.108 Port 091ADefault TFTP block size set to: 512 bytesThere were no options detected in the TFTPEthDown::TFTPD_OPEN::boot.bin-EbootSendBootmeAndWaitForTftpBL_IMAGE_TYPE_BINDownload
file information:-----------------------------------------------------------[0]: Address=0x80101000 Length=0x0802a99c Save=0x80001000-----------------------------------------------------------Download file type: 1TFTP: Desktop losing ACK, block number = 23211,
Ack againTFTP: Desktop losing ACK, block number = 23211, Ack againTFTP: Desktop losing ACK, block number = 40339, Ack againrom_offset=0x0.ImageStart = 0x80101000, ImageLength = 0x802A99C, LaunchAddr = 0x8010FDFCCompleted file(s):-------------------------------------------------------------------------------[0]:
Address=0x80101000 Length=0x802A99C Name="" Target=RAMROMHDR at Address 80101044hGot EDBG_CMD_JUMPIMGGot EDBG_CMD_CONFIG, flags:0x00000000Launch Windows CE image by jumping to 0x8000fdfc...Windows CE Kernel for ARM (Thumb Enabled) Built on Sep 14 2011 at 17:32:20ProcessorType=0c08
Revision=2 CpuId=0x413fc082OEMAddressTable = 8010fe9cOAL: CPU revision 0xffffffffOAL: CPU L2 Aux register 0x400042CPU CP15 Control Register = 0xc5387fCPU CP15 Control Register = 0xc5387f--- High Performance Frequecy is 32768 khz---Changed KITL zone mask to
0x00008001DM9000DBG_Init: IndexPort = 0x15000000 , DataPort = 0x15000000 DM9000 Mac Address: bc:37:e1:87:90:ffDM3730 Found DM9000 ID:90000a46DM9000 Chip Revison: 0x19DM9000 Work in 16 Bus WidthDM9000 Mac : bcDM9000 Mac : 37DM9000 Mac : e1DM9000 Mac : 87DM9000
Mac : 90DM9000 Mac : ffLink on ethernet at:100 MbpsDM9000_Init OK.WARN: KITL will run in polling modeVBridge:: built on [Dec 30 2011] time [18:17:11]VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytesTx buffer [0xA8150F40] to [0xA8154F40].Rx buffer [0xA8154F60]
to [0xA8158F60].VBridge:: NK add MAC: [BC-37-E1-87-90-FF]Connecting to Desktop!Received config for unrecognized service DBGMSG