Standard in the LLC Sublayer and use the CSMA/CD method in the Mav sublayer.d) data transfer rate increased to 100Mbps.E) provides 10Mbps and 100Mbps rate auto-negotiation function.IEEE802.3U Architecture Diagram:2) Fast Ethernet media Dedicated interface MiiTo mask the different physical details of the lower layers, 100BASE-T provides a common transparent interface for Mac and high-level protocols with a 100M transfer rate, with the same functionali
repeater to expand the topological distance of the network. This is because signal attenuation occurs after long-distance transmission. The function of a repeater is to sort out the signals that have been degraded and become incomplete, re-generate a complete signal and continue transmission. A repeater is the predecessor of a general hub. A hub is a multi-port repeater. Take the
interface also changes accordingly. To transmit data streams over Mbps on five unshielded twisted pair wires, 100BASE-T adopts multi-level MLT-3 and channel coding adopts 4B/5B encoding. In addition, to facilitate the upgrade of the user's network from 10 Mbps to 100 Mbps, The 100BASE-T standard also provides the automatic speed listening function. This function allows an adapter or switch to send at 10 Mb
first! Connect to the third server and test again!
What brand of switch is this! Let me see, I ......, I shouted, "Mr. Wang, which vswitch did you buy! "Mr. Wang hurried over." Didn't you say it was 100 Mb/s? You see, isn't it? "He pointed to the 100Base-TX and showed it to me. "Hi, I said you should wear a pair of glasses. Do you think this is a Switch? This is clearly the HUB, which is clearly written ab
maximum segment length is 500m, baseband transmission method;10base-2 using fine coaxial cable, the maximum segment length is 185m, baseband transmission method;10base-t using twisted-pair cable, the maximum segment length is 100m;1base-5 uses twisted-pair cable, the maximum segment length is 500m, the transmission speed is 1Mbps;10BROAD-36 uses coaxial cable (rg-59/u CATV), the maximum network segment length is 3600m, is a kind of broadband transmission mode;10BASE-F uses optical fiber transmi
PABX. In a data network, this device is a host or hub. In a star network, you can easily add and reduce devices without affecting the work of other devices in the system. adjourned
Wiring nouns
100BASE-T4 uses 4-line MBIT/S Fast Ethernet for 3-class cables.
100BASE-TX uses 2-line MBIT/S Fast Ethernet for 5-class cables.
100vg-anylan the mbit/s LAN, which was
Term or symbol
English name
Chinese name or explanation
ACR
Attenuation to Crosstalk Ratio
Moderate reduction-crosstalk attenuation rate
ADU
Asynchronous Data Unit
Asynchronous Data Unit
ATM
Asynchronous Transfer Mode
Asynchronous transmission mode
BA
Building Automation
Building Automation
BD
Building Distributor
Building wiring equipment
B-ISDN
Broadband ISDN
Broadband ISDN
10BASE-T
10AB
all 4 pairs of wires be used for signal transmission, while the other two standards require only 2 pairs of wires. The most common in Fast Ethernet is the 100BASE-TX standard, so when buying a twisted pair used in a 100M network, some network vendors or companies provide only 2 pairs of twisted pair, on the grounds that Fast Ethernet requires only 2 pairs of wires to transmit information.
7. When making the straight line, is not sure to follow the 56
Fast Link pulse
Auto-negotiation takes place using fast
Link pulse (random) signals. these signals are a modified version of the normal link pulse (NLP) signals used for verifying link integrity, as defined in the original 10base-t specifications. the specified signals are generated automatically at power-up, or may be
Selected manually through the management interface to an auto-negotiation device.
The Fast Link pulse signals are designed to coexist with NLP signals, so that a 10base-t device
the computer. The connection is still unavailable. Note that the vswitch has an uplink port. I tried to connect the uplink port of one vswitch to the normal port of the other vswitch after the test. After testing, it is found that the local area network uses a 100base-tx hub with a similar serial number as a switch. After debugging, the fault is rectified immediately.
A
There are many different classifications of fiber optic transceivers, and most of the attention is being paid to categories that are differentiated by fiber connectors: SC connectors, fiber transceivers, and fc/st connectors.
When using a fiber-optic transceiver to connect to different devices, you must be careful to use different ports.
1, optical transceiver to the 100BASE-TX device (switch, hub) conn
channel or link.
Length: Maximum wiring length.
Near-string attenuation: signal coupling between adjacent transmission and receiving lines.
11. Comparison of MHz and MBps
The attenuation and NEXT of cables can be obtained from the scanning measurement, and the specified test range is from 100 MHz to MHz. The attenuation and NEXT values indicate the sine voltage loss at a specific frequency and cannot be confused with the bandwidth limit value, bit rate, or port (that is, 622MBps does not mean t
. The attenuation and NEXT values indicate the sine voltage loss at a specific frequency and cannot be confused with the bandwidth limit value, bit rate, or port (that is, 622MBps does not mean that the wiring is limited to 622 MHz ). According to the design objectives, modulation and signal processing accompanied by amplitude, frequency, or phase changes are usually used to change the desired bit rate to the acceptable signal sending rate (Porter ).
12. Data Transmission
The design goal determi
characteristics. The most commonly used in the network is the three types of lines and five types of lines, at present there are more than six types of lines. The third kind of twisted pair is commonly used as 10Mbps Ethernet data and voice transmission in LAN, which accords with the standard of IEEE802.3 10base-t. The fifth type twisted-pair line currently occupies the largest LAN market, the highest rate can reach 100Mbps, conforms to IEEE802.3 100base
A LAN interface Cable Standard 1, 10base-t: twisted-pair cable, the general use of RJ-45 connectors, the maximum effective transmission distance is from the hub 100m, even the high-quality 5-type twisted pair can only reach 150m. Its matching resistance is 120 euro. 2, 10BASE5: Coarse coaxial cable, the use of plug-in joints, baseband signal, the maximum support length of 500m, the maximum number of segments is 100. Its matching resistance is 75 e
I. LAN interface cable standards
10base-t: twisted pair cable, generally using RJ-45 connector; maximum effective transmission distance is 100 m from the hub, even high-quality 5 category twisted pair can only reach 150 m. The matching resistance is 120 Euro.
10base5: coarse coaxial cable with plug-in connector and baseband signal. The maximum supported length is 500 m and the maximum segment is 100. The matching resistance is 75 Euro.
10base2: thin
I. LAN interface cable standards
1, 10Base-T: twisted pair cable, generally use RJ-45 connector; maximum effective transmission distance is 100 m from the hub, even the high-quality Category 5 twisted pair can only reach 150 m. The matching resistance is 120 Euro.
2. 10Base5: coarse coaxial cable with plug-in connector and baseband signal. The maximum supported length is 500 m and the maximum segment is 100. The matching resistance is 75 Euro.
3. 10Ba
First, LAN interface cable standard
10BASE-T: Twisted-pair cable, generally use rj-45 connector, the maximum effective transmission distance is from the hub 100m, even high-quality 5 twisted pair can only reach 150m. Its matching resistance is 120 euro.
10BASE5: Coarse coaxial cable, with insert-type joints, baseband signal, maximum support length of 500m, up to 100. Its matching resistance is 75 euro.
10BASE2: Fine coaxial cable, the joint uses th
10BASE-T: Twisted-pair cable, generally use rj-45 connector, the maximum effective transmission distance is from the hub 100m, even high-quality 5 twisted pair can only reach 150m. Its matching resistance is 120 euro.
10BASE5: Coarse coaxial cable, with insert-type joints, baseband signal, maximum support length of 500m, up to 100. Its matching resistance is 75 euro.
10BASE2: Fine coaxial cable, the joint uses the industrial standard BNC connector t
network cabling, this article mainly introduces the correct identification and selection of five types of UTP.
1. transmission speed
The quality of twisted pair wires is one of the key factors that determine LAN bandwidth. Some manufacturers wrap line pairs used in Class 3 or Class 4 UTP cables in Category 5 UTP, which is difficult to identify for general users. The so-called "five types of UTP" cannot reach a data transmission rate of Mbps, and the maximum is 10 Mbps or 16 Mbps. A simple ident
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.