160gb ide hard drive

Hard drive bad reason is many, and our daily illegal operation and use of a direct relationship, then what wrong operation will cause the hard drive appear bad way? Hard drive bad road can be said to be a fatal failure of the

connected to the motherboard's IDE interface, but if you are using an earlier DMA/33 data cable, there is no such requirement. After you complete this step, the installation on the hardware is complete. Next we can turn on the power of the computer, and enter the bios of the motherboard, you can see that the BIOS has detected two hard disk capacity and master-slave relationship, which means that the two

technology matures, more and more motherboards and hard disks are starting to support SATA (Serial ATA), and SATA interfaces are gradually replacing the traditional pata (parallel ATA) trend. What is the difference between SATA and PATA in transmission mode, and what are the advantages of SATA relative to Pata? This is the topic that this article needs to discuss. 　　What is Parallel ATA ATA is actually an interface standard for

Hard drive bad reason is many, and our daily illegal operation and use of a direct relationship, then what wrong operation will cause the hard drive appear bad way? Hard drive bad road can be said to be a fatal failure of the

Q: I installed a couple of hard drives a few days ago I loaded two hard drives onto an IDE line, and the hard drive was not recognized. Later, the main disk and CD-ROM installed together, found the hard

menu under main. Under the onboard ide operate mode, you can select two ide operation modes: compatible mode and enhanced mode (compatible mode and enhanced mode ). The compatibility mode is compatible mode, which can be understood as ing the SATA hard disk port to the corresponding port of the parallel port ide chann

Failure Phenomenon: The taskbar "Safely Remove Hardware" appears in the delete hard drive c,d,e,f and the optical drive, although the local hard drive deleted, but the optical drive accidentally deleted, to light

When you start your computer, you do not see the Windows splash screen, but instead appear the "Non-system disk or disk Error,replace disk and press a key to reboot" (non-system disk or disk error) prompts, which is the common hard Disk failure-Unable to boot the system. (i) Hard failure causes hard drive to boot The

temperature, the difference is also possible. Generally speaking, the motherboard, hard disk temperature is lower than the CPU, the motherboard is generally 40-60 degrees between the temperature is acceptable, hard disk temperature, the normal IDE or SATA hard disk temperature should be below 55 degrees is normal. Wh

Now because the data is more and more large, so that our hard disk memory is not enough, so we need to add a hard disk, to increase the capacity of memory. Dual hard disk configuration is not so simple, it has a lot of attention to the place, such as power problems, as well as the main hard disk, from the disk of the p

the built-in IDE interface, but he is not the only way to interface, the other is Scsi,ide external, the IDE outside the extraction box and 2, one through the mouth to connect, the other is the most popular USB interface now, The biggest advantage of this external extraction box is that it is used in environments where there is no temporary need for large amount

BT and thunder do not hurt the hard drive, you will know after reading Reference someone's words first. Someone thinks Bt and thunder hurt the hard disk: Why does frequent read/write damage the hard disk? The lifetime of the head is limited. Frequent reading and writing will accelerate the wear and tear of the head arm

remove the motherboard for observation, then found on the back of several places covered with dust, which is located in a IDE1 interface of the solder point, the accumulation of dust almost covered the solder. The dust 淸 clean, fixed the motherboard, fitted the accessories, restart the computer, successfully entered the Windows7 flagship version, everything back to normal. Note: Dust is the computer's invisible killer, the accumulation of dust hindered the heat dissipation, easy to damage comp

, which must be based on the hard disk conditions to set up, otherwise it is likely that there will be other problems. This kind of situation is not difficult to solve, as long as the motherboard BIOS instructions and the hard disk itself, the correct settings can be resolved. Third failure: A primary partition fails to start the hard

and Ultra320 SCSI all represent a specific hard disk interface, and their speed varies considerably. HDD Interface Classification Ide IDE's English is all called "Integrated Drive Electronics", namely "Electronic Integrated Drive", the common 2.5-inch IDE