3com switch configuration

Tags: Cisco configuration switch Management address and default gatewayConfigure the switch remote management address and default gatewayThe topology diagram is as follows:650) this.width=650; "Src=" Https://s1.51cto.com/oss/201710/29/1b8f7b6af37801733cf03704e748d09a.png-wh_500x0-wm_3 -wmp_4-s_475699717.png "title=" 57.png "alt=" 1b8f7b6af37801733cf03704e748d09a.

In the work of network management, the Internet Café switch configuration must be mastered and skilled, because this is a complex process, for some of the new network management, may also lack of experience. This article specifically explains the Internet Café Switch Configuration tutorial, for reference only. Differe

using MacOS. The following video shows several ways to debug a switch using a serial cable from MacOS.650) this.width=650; "src=" Https://s1.51cto.com/wyfs02/M02/8E/26/wKioL1i3fg2C94_-AAFSKsZbT_s636.jpg "title=" 25097475_4.jpg "width=" "height=" 319 "border=" 0 "hspace=" 0 "vspace=" 0 "style=" WIDTH:600PX;HEIGHT:319PX; "alt=" Wkiol1i3fg2c94_-aafskszbt_s636.jpg "/>After the configuration IP of the

Whether it's on a Cisco router or a network device such as a Cisco switch, the standard ACL access control list is always unable to match both the traffic source address and the destination address, nor does it meet the requirements of the "granular" control of the current network world, such as: A service function that allows access to a server, However, pinging the server is not allowed. In this case, an extended ACL is needed to replace the standar

Cisco switch QoS Speed limit configuration steps:1. Enable Global QoS2. Set the ACL matching traffic3. Set a class-map to match the ACL set in the second step4, set a Policy-map match Class-map, and then define a series of policies here, limit the bandwidth bitwise (BIT) for the calculation, burst in bytes (byte) calculation5, apply the POLICY-MAP to the corresponding interfaceMLS QoSIP Access-list Extended

The following is the author of the video course of a PPT course content, introduces the Huawei VRP System user Interface main configuration method, and a real Telnet remote login experiment to verify the correctness of these configurations. The video links for this course are as follows ( free to watch ): http://edu.51cto.com/lesson/id-22512.htmlFirst, the VRP user interface configuration steps650) this.wid

1. Experimental topology650) this.width=650; "Src=" https://s4.51cto.com/wyfs02/M00/97/B2/wKiom1kxPDizomXqAABw1vEUgaA990.jpg-wh_500x0-wm_ 3-wmp_4-s_3605733301.jpg "title=" rspan.jpg "alt=" Wkiom1kxpdizomxqaabw1veugaa990.jpg-wh_50 "/>2. Switch configuration4F-IDC-01 ConfigurationVLAN 100Remote-spanMonitor session 1 Source VLAN 13Monitor session 1 destination Remote VLAN 1004F-IDC-04 ConfigurationVLAN 100Remote-spanMonitor session 2 Destination interfac

The previous two posts have explained how to back up the configuration file, the function of the expect script is to provide interaction, log in each switch to perform a backup command to copy it to the TFTP server. But in our normal work, the general backup method is to dis cu or sh run and then copy the information on the screen, in fact, the previous script can be slightly modified to use this method to

As an IT network siege lion, backup network equipment configuration is one of our daily work, but with the increase of equipment, previously very erasy manual backup, now also more and more time spent, Bo Master as an IT lazy people, believe there must be lazy way!Pre-Preparation: 1, NTP server 2, ftp/tftp server 3, command configuration1st: Time in the network is important, so you need NTP server to build NTP server with Windows Linux if you have an