pressure of about V, which can cause serious personal injury. Therefore, never try to disassemble or change the LCD screen to avoid high pressure. Unlicensed repairs and changes will temporarily or permanently disable the display. So when your hands and feet are really idle, it is best to play with the lawn cutter or other playways, that is, do not touch the delicate and dangerous lcd1.(
can display per second. Generally, when the screen display speed exceeds 25 frames per second, the human eye will regard the rapidly changed screen as a continuous screen without any pause, therefore, the response time will directly affect your visual experience. When the response time is 30 ms, the display can
can be displayed, each line of 16 characters LCD module (display characters and numbers ).Because the 1602 LCD is powered by 5 v, the pin height is 5 v. Unlike 51 Single-chip I/O Output High Level 5 v, STM32 high level only 3.3 v
MPU writes the data to Module 4:Figure 4 MPU write data to module diagram①mpu from the module read the data 5:Figure 5 MPU reading a data map from a moduleSecond, serial connection sequence diagramSerial data transfer is done in three bytes:First byte: Serial Control-format 11111ABC①a for data transfer Direction control: H represents data from LCD to mcu,l for d
of light) source;(4), Ito transparent conductive layer: to provide transparent conductive path;(5), Photo Spacer: Provide a fixed height to color filters and TFT Glass substrate. As the space to pour into the liquid crystal, and as a support for the upper and lower layers of glass.2. Side view of TFT-LCD structureFirst, TFT-LCD
image data area directly stored in the image of the RGB data, where each pixel point of data in B, G, R order. The data structure of each pixel point is shown in 6.Figure 6 Data structure of an image array2.4) Since the data in the image data array is stored from the last line of the picture, the image is displayed in a progressive scan from the lower left corner of the image, from left to right, bottom to top.2.5) for the LCD on the s3c2410 or PXA25
Analog and digital interfaces for LCD display
1. Analog interfaceAnalog and digital video sources have existed for a long time. Analog videos are often used on desktops, while digital videos are popular in laptops. Currently, a large number of computers use analog video output, which ensures that the support of analog interfaces ca
12864 LCD uses 16*16 lattice, 128 characters (8*16 lattice), and 64*256 lattice display RAM (gdram ). parallel or serial control mode is used with external CPU interface compaction.
The second line of the random number 0-9 displayed on 12864 shows www. csdn. Blog
The third line shows "Seeking for 07 blogs"
The fourth line shows "welcome"
Below is the basic code
# Include # Include # Include # Define uchar
12864 LCD uses 16*16 lattice, 128 characters (8*16 lattice), and 64*256 lattice display RAM (gdram ). it adopts parallel or serial control mode with external CPU interfaces.
The second line of the random number 0-9 displayed on 12864 shows www. csdn. Blog
The third line shows "Seeking for 07 blogs"
The fourth line shows "welcome"
The following is the main code:
# Include # Include # Include # Define uchar
gui_application_entry(void *parameter){struct Rtgui_app *app;struct Rtgui_rect rect;App = Rtgui_app_create ("Gui_demo");if (app = = rt_null)Return... ...Then locate the code near 64 lines to 120, starting with Demo_view_box (), until the code between Rtgui_win_show () is left Demo_view_button (), the other code is commented out and modified as follows:Then save, re-scons the compilation, download to the Development Board, you can see the following effect:As a result of the shooting, the foregro
Liquid Crystal has 1 or 2 ends as the power supply, 15, 16 for the back light source; to prevent the Direct Addition of 5 V voltage burned back light, 15 pin a 10 euro resistance for throttling.
The LCD 3 end is the LCD contrast adjusting end, and uses a 10 k euro potentiometer to adjust the LCD contrast,
The four ends
);
}
4, to map the address to write data, draw framebuffer.
void Fb_drawbmp (UINT height,uint width,unsigned char* pdata)
{uint x,y,cnt
;
UINT a = height*width*3;
UINT CNT1 = 0;
uint* p = fbmmap;
for (x=0 x
5, in the USB camera Operation Readfram (), will Fb_drawbmp () into the inside, the camera collected data into RGB, directly written to framebuffer, you can complete the LCD
interference away from the installation of the video card (such as hard disk) and check whether the screen disappears. If it is determined that the electromagnetic shielding function of the video card is not enough, you should change the video card or make a self-made screen cover.
Step 4: Check whether the resolution or refresh rate of the monitor is set too high. The resolution of the LCD is generally lower than that of the CRT
-------------------------------------------
Target: LCD screen driver and display.
Understand the control method of gpio, and write a simple menu Test Program (including the display of colored Chinese characters and static pictures)
--------------------------------------------
I. Glossary
1. What is a gpio port? What are the related resources in mini2440?
A:
2.2
DescriptionYour friend just bought a new computer, the most powerful computing tool he has ever used is a pocket calculator. Now, looking at his new computer, he is a little disappointed because he prefers the LC monitor on the calculator. So, you decided to write an LC display style program to help him display the numbers on the computer.InputThe input includes several lines, each with two integers. The in
problem needs to be located in the Surfaceflinger module.The second case: if the LK start stage shows abnormal, such as the Phone boot logo interface display abnormal.1). You can first replace the logo image with a simple left black right white equal size picture, such as:When the normal display is measured separately, the relevant MIPI timing diagram is displayed when the anomaly is shown.The waveform of
This article is reproduced in: workshop!
Display the time, date, and week on lcd1602
Because SDRAM is used, first we add a PLL
Input clock 50 MHz
The output clock C0 is 50 MHz and the phase is-75 degrees. The clock is provided to the SDRAM and the pin is named sd_clk.
C1 50nhz, with a phase of 0 degrees. It provides a clock signal to the nioss-clk and is connected to the nioss-clk.
1. enable the system file system, add the CPU, and sele
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.