8 port infiniband switch

]rulepermitipsource10.10.1.10destinationany [SwitchA-acl-link-3000] rulepermitipsourceanydestination10.10.1.10 3. Will pass through the port G1/0/1, matches the ACL rule the message to mirror to the monitoring port [SWITCHA]INTERFACEGIGABITETHERNET1/0/1 [SWITCHA-GIGABITETHERNET1/0/1] Mirrored-toinboundip-group3000monitor-interface [SWITCHA-GIGABITETHERNET1/0/1] Mirrored-tooutboundip-group3000monitor-inter

allows packets sent by default VLAN without tags. 1.4 Fabric port Mode The Fabric port is the port between units in IRF. It is only used for interconnection between units and cannot connect users. 2 Application of Hybrid port Mode By introducing the various link port modes

the direction of message flow limit to the speed limit to 3Mbps [Switcha-ethernet0/1]line-rate Inbound 1 The total rate at which a message is sent or received by the port is indicated here at 8 levels, with a value range of 1~8, which means that when the port is working at a 10M rate, 1~

) #Exit//Exit VLAN configuration state sw02(config) # interface Ethernet G1//Enter port configuration status sw02(config-if) #switchport Access VLAN 100//Configuring VLANSW02 for Ports(config-if)Exit//exit port configuration status sw02(config)Exit//exit configuration State sw02#show VLAN//Show VLAN configuration VLAN Name PortsTypeAuthorization---------------------------------------------------------------

Huawei switch Port monitoring), and the Port connecting to the listening device is called the "analysis Port" Analyzer Port ). Run the following command to configure a port listener for a Huawei switch:Feature rovingAnalysis add,

I. Port Mirroring concept: Port Mirror is used for network performance monitoring. It can be understood as follows: Establish an image relationship between port A and port B. In this way, data transmitted through port A will be copied to

Session 1 Port SecurityThe MAC address in the network is the constant physical address in the device, the control of the MAC address access control the switch port access, so port security is also the security of the Mac. In the switch, the cam (content addressable memory, t

In the tree menu on the left of the switch management interface, select switch (switch) >>> Ports (port) >>> "portmirroring" (port mirroring), and the right opens "portmirroring" (Port Mirroring) page. The parameters in this page

置SNMP协议的读团体字符, must be consistent with the settings on the switch.⑥units #设置端口流量的单位.⑦use Custom Multiplier # tick, and set the value to 8, if not set, units Unit is bps.⑧update interval #根据服务器的性能和监控的设备数量来设置, the default is also available.650) this.width=650; "title=" 8 "style=" border-top:0px;border-right:0px;background-image:none;border-bottom:0px; padding-top:0

range is 1~4094. When you configure the watch port, if you do not specify a VLAN, the type of the observed port is local mirroring, and if you specify a VLAN, the type of the watch port is the remote mirror. 2. Configure the Mirror Port#将ETHERNET0/0/1----ETHERNET0/0/10 interface is configured as a mirrored

To configure a vswitch port image, experts can understand the following knowledge about the vswitch port image configuration. You only need to complete the vswitch port image configuration in a few minutes. The local connection is also mentioned in this article. Vswitch images such as 3026]Vswitches such as S2008/S2016/S2026/S2403H/S3026 support

-Gigabit Switch with excellent performance does not have HOL. The test time is 15 seconds. Deep test on address learning rate and address table The address table thoroughly tests the number of MAC address tables for 24 full gigabit switches. The address learning rate checks the speed at which 24 full Gigabit Switches learn MAC addresses. We have used 24 ports A, B, and C of all gigabit switches. Ports A and B are used for sending learning frames and t

Huawei switch Port isolation, the implementation of the switch port is not interoperable, directly under each interface configuration port-isolate enable command. However, the Port-isolate command cannot be configured on an Allied

When maintaining the dormitory network for a few days, I encountered a very unique problem at the time: No matter how the 20 Ports of the vswitch on the fourth floor are connected, the link cannot be connected; when the switch enters, the port cannot be enabled; there is no problem connecting to other ports. I thought it was because the port broke down. Later I h

one thousand m switch. In general, the price of the desktop Gigabit Switch is still relatively approachable, making it possible for small offices to speed up in an all-round way, the cheapest Gigabit desktop switch costs only a few hundred yuan, which is very affordable. These products also have some characteristics in parameter indicators. The most important pa

bandwidth description: When the Ethernet frame is 64 bytes, the fixed overhead of the 8 byte frame header and the 12 byte frame gap must be considered. Therefore, the packet forwarding rate of A 1-gigabit Ethernet port when forwarding a 64-byte packet is 1.488 Mpps. The 10-in-10 Gigabit Ethernet packet forwarding rate is 148.8 kpps.◆ For 10-Gigabit Ethernet, the packet forwarding rate of a wire speed