Discover add vpn configuration iphone, include the articles, news, trends, analysis and practical advice about add vpn configuration iphone on alibabacloud.com
System environment: Windowsserver2008r2enterprise (fully installed)1, Configuration preparation work1.1, click on the "Start" to the right "Server Manager"1.2, click "Role" in "Server Manager"1.3, in the "role" click on the right to select the translation "Add Role", click "Next"1.4, in the "role" select "Network Policy and Access Services", click "Next"1.5, click "Next"1.6. Select the Routing and Remote Ac
When synchronizing data across computer rooms, VPN links are often used because of the high security. Online on this aspect of the article, I really did not find that I want, is too simple, Daniel do not want to write it, or too difficult to do it?The following example illustrates the establishment and use of VPN links
First, install the VPN server on the remote
Lab Environment
There are company offices, Beijing branch and Shanghai Branch, and Beijing and Shanghai branches need to access the file servers and web servers of the company.
Configure as shown in the following figure:
Router configuration
Beijing Branch
Route (config) # hostname BJROUTE
BJROUTE (config) # inter s0/0
BJROUTE (config-if) # ip add 220.231.61.165 255.255.255.0
BJROUTE (config-if) # no sh
This article provides a comprehensive explanation of LAN networking. During VPN networking for small and medium-sized enterprises, we will encounter many setup problems, here we will introduce you to a configuration scheme for setting up a VPN Server in a LAN, which is illustrated in detail throughout the networking process.
Next I will use Win2000 on the
connected to the eth1 interface of firewall.VLAN2: 192.168.2.0/24VLAN3: 192.168.3.0/247. the intranet of firewall B is 10.30.30.0/24, and the Intranet host is set to 10.30.30.2/24. It is directly connected to the eth1 interface of firewall B.8. The VLAN of firewall A and the Intranet of firewall B communicate with each other through VPN.
Specific configuration process:
1. First configure the wired connection in the VPN configuration.
2. perform the following operations:Sudo gedit/etc/Network/interfaces
Auto LoIface lo Inet loopbackAuto eth0Iface eth0 Inet staticAddress xxxxNetmask xxxxGateway xxxx
Sudo gedit/etc/resolv. confNameserver 10.10.0.21
ThenSudo/etc/init. d/networking restart
Last
Sudo VPN-Connect
3. Install the
Firewall-based Easy VPN configuration process
Objective: To enable a client on the remote Internet to access internal resources of the LAN through an encrypted tunnel by making Easy VPN on the gateway ASA firewall device.The following figure shows the experiment topology. R1 is a router inside the lan. C1 connects to the VMnet1 Nic and uses the Windows 7 operatin
# Reference configuration# Localip 10.0.0.1# Remoteip 10.0.0.100-200 Localip is the local IP address, that is, the local IP address.The remoteip is the IP address allocated to the remote host. It is usually set to a continuous ip segment.4. Modify the/etc/ppp/options.ppt pd file to complete DNS modification for the VPS server. The code is as follows:Copy code Ms-dns 8.8.8.8Ms-dns 8.8.4.4 5. Edit/etc/ppp/chap-secrets and configure the
network relationship. Other users in the middle of the network will not be able to access the network.
The following example describes how IPSec is configured on a H3C device:
Equipment requirements:
This experiment employs 3 h3c2600 routers and a three-layer h3cs3526e switch.
Test requirements:
Using IPSec to establish a VPN allows the head office to interoperate with each branch, and the branch can communicate with each other
Head Office Ro
Graphical configuration of using cisco ipsec vpn by subway in ubuntu 13.04By default, ubuntu only provides pptp vpn connection configuration. To use a cisco ipsec vpn, you must first install vpnc. If you are not familiar with the command line, you need to solve this problem
LinuxLowerVPNClient (p t p) Configuration
Linux: Kernel kernel-2.6.9-42.EL
You can go to the site: http: // pptpclient.sourceforge.net/
Required software:
Kernel-devel-2.6.9-42.EL (built-in system)
Dkms-2.0.10-2.fc5.noarch.rpm
Dernel_ppp_mppe-0.0.5-2dkms.noarch.rpm
The above three files are usually installed when you set up the Linux VPN Server. You can run the # rpm-Q command to view them.
(Example: # rpm
Steps:
1. Log On As the domain administrator. Win2003server configuration.
1. log on to the console and connect to start à Administrative Tools à Routing and Remote Access --> server (computer name) right-click an electric shock-> click "configure and enable Routing and Remote Access" à next à at "configuration" Page choose "remote access server (dia-up and VPN)
1, create VPNRouting and Remote Access--configure and enable and route remote access--Custom configuration--Select VPN access, NAT, and Basic Firewall.
2,VPN ConfigurationIP Routing (nat/Basic Firewall)--New interface (select Local network card)--select "public interface to connect to the Internet" and choose "Enable NAT (E) on some interfaces--
First, install VPN service
The code is as follows
Copy Code
sudo apt-get install pptpd
Second, the next configuration pptpd service
There are three main configuration files
The code is as follows
Copy Code
/etc/pptpd.conf/etc/ppp/pptpd-options/etc/ppp/chap-secrets
Let's change the pptp
The L2TP tunnel (L2TP tunnel) refers to the logical link between the second-tier Tunneling Protocol (L2TP) endpoints: LAC (L2TP access aggregator) and LNS (L2TP network server). When LNS is a server, LAC is the initiator of the tunnel and waits for the new tunnel. Once a tunnel is established, the new communication between this point will be two-way. In order to be useful to the network, high-level protocols such as Point-to-Point Protocol (PPP) are then passed through the L2TP tunnel.
Today, j
Summary of configuration formats of dynamic routing (ripV2, ospf, VPN, bgp, IS-IS)1. r12002router rip enable rip Protocol no atuo-summary disable automatic summary of version 2 2 network x mask x declaring the network segment (the subnet mask is a positive mask, mask can be disabled. 2. Enable the ospf protocol for ospfrouter ospf x, and add the Process Code rout
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.