Ubuntu9.04 download TP-link wn322g + 2.0 (ar9271 chip) unlimited NIC Driver
Software required:Htc_9271.fw (previously, ar9271.fw, and now the new version is htc_9271.fw)Compat-wireless-2.6.tar.bz2Reference Document (Official Website ):Http://linuxwireless.org/en/users/Drivers/ath9k_htcHttp://linuxwireless.org/en/users/DownloadHttp://linuxwireless.org/en/users/Drivers/ath9k_htc/devices
1. Copy the htc_9271.
1. PrefaceFind a wireless network card for mercury mw150u, which can be automatically identified under Ubuntu 11.10, but it will not be recognized if it is changed to 10.04. Think about it as if the driver is not installed properly.I found and TP-link TL-WN721N, TL-WN722N, fast fw150u, are using the chip of atheros ar9271.Root @ Ubuntu :~ # Uname-Linux Ubuntu 2.6.32-33-generic # 70-ubuntu SMP Thu Jul 7 21:09:46 UTC 2011 i686 GNU/LinuxRoot @ Ubuntu :~
I believe many children's shoes with wireless network card is TP-LINK TP-WN722N, this network card is using the AR9271 Atheros this new product, low power, low heat dissipation, signal stability, wireless NICs using the AR9271 chip also have Fast FW150UD and Mercury MW150UD ...... (well, in fact, these three NICs are one, and the driver can also be used)After www.2cto.com installed the Win8 system, it was f
Https://wireless.wiki.kernel.org/en/users/drivers/ath9k_htc
The descriptionDownload HTC_9271.FW
Http://git.kernel.org/cgit/linux/kernel/git/firmware/linux-firmware.git/tree/htc_9271.fw
Put firmware in Ubuntu/lib/firmware directory6. Confirm the Ubuntu kernel version and download and install the wireless card driver1) Confirm kernel version information in the current Ubuntu virtual machineUname-2.6. 32-21-generic #:i686 gnu/linux 2) Download DriverNot to be conti
Description
The airmon-ng is used to convert the wireless interface between the managed and monitor modes. Enter the Airmon-ng command without parameters, and the current interface state is displayed. usage
Airmon-ng
Or:
Airmon-ng
Where: usage Examples
1. View the status of each interface:
~# airmon-ng
PHY Interface Driver Chipset phy0 wlan0 ath9k_htc Atheros Communications, Inc. AR9271 802.11n
2. Check the process affecting Aircr
I. USB INFINITE network cardUsing Kali Linux, first prepare a USB external network adapter for Kali system, note that the built-in NIC is not suitable for penetration testing.Linux system instructions are more obscure than the average person, it is best to choose a drive-free type, eliminating the tedious steps of various configurations.Two. Common chip typesUsed to crawl wireless packet stability and compatible with the three of the better chip:1.rt3070 (L)/rt5572: Plug and Play supports promis
What can I do after the Internet? : Http://www.bkjia.com/Article/201405/304310.html, I do not know you have seen? You may also have heard about the hot-rising vro security vulnerabilities. Do you think your vro is still safe? :) the security of your vro is getting hotter and hotter. If something goes wrong, you must be beaten, so today, I will give you the knowledge of wireless network security under shoes and science. Do you think it is safe to add a secret? Break through this first line of def
Objective:Previously introduced the foreign wireless security audit equipment The WiFi Pineapple nano sslsplit modules and Ettercap modules and experiments.In the process of playing WiFi Pineapple nano device, given that the individual has only a few network cards, testing to find that the Nano can support the network card chip has: rtl8187l, RT3070, AR9271, RT5370 ..., Friends in the process of their own testing if you find that the network card is n
the external active USB HUD. Go to the command line interface and enter the following command
sudo lsusb
Copy CodeYou can see that when the command is finished, all attached USB devices are displayed, and the last line is usually your wireless network card, and the result of my own test shows that
[Email protected] ~ $ sudo lsusb
Bus 001 Device 001:id 1d6b:0002 Linux Foundation 2.0 root Hub
Bus 001 Device 002:id 0424:9512 Standard Microsystems Corp.
Bus 001 De
1. Make sure that your kernel can recognize your USB Nic before porting the wireless Nic. After inserting the NIC, the following information is displayed:
[Root @ friendlyarm/] # USB 1-1: USB disconnect, address 2USB 1-1: new full speed USB device using s3c2410-ohci and address 3USB 1-1: new USB device found, idvendor = 0133, idproduct = 8176USB 1-1: new USB device strings: MFR = 1, Product = 2, serialnumber = 3USB 1-1: Product: 802.11n WLAN AdapterUSB 1-1: Manufacturer: RealTekUSB 1-1: serialnu
Reprinted please indicate the source: http://blog.csdn.net/ruoyunliufeng/article/details/38515423
This article mainly describes how to build a remote video monitoring environment. It will be designed to build a network, and some applications and libraries will also be transplanted.
1. Configure the kernel
1. Support for UVC (USB camera)
Make menuconfig[*] Video capture adapters (new) --->[*] V4l USB devices (new) --->2. Support for wireless NICs (atheros ar
Compile the Raspberry Pi 2 generation B OpenWrt firmware to implement the wireless router and nodogsplash authentication function. openwrtnodogsplash
Final function:
The main features of the wireless router, network port WAN Access, USB wireless Nic AP hotspot output, connected to wifi, jump to the authentication page, click the authentication to access the Internet, the effective time is 10 minutes, after successful authentication, the system automatically accesses the specified URL.
Compiled r
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.