arm64 board

How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet) How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet) ---------- A newcomer asked questions at the csdn Forum Recently I want to buy a 2440 Development Board. To learn about embedded

AC6102 Development Board USB3.0 test and use instructionsOverviewThe AC6102 incorporates a cypress-launched high-performance USB3.0 transmission chip cyusb3014,cypress called EZ-USBFX3. The chip features strong, powerful, simple interface and is ideal for use in a variety of applications where high-speed data transmission is required, following an introduction to the chip from the EZ-USBFX3 data sheet:Cypress EZ-USBFX3 is a new generation of USB3.0 pe

After I got the OK2440 Development Board, I got the development board yesterday after connecting to the nfs server. After I clicked it, I found that the LCD was really bad. No money is required. Ke, I entered the topic. Today, I tried to connect to the company's computer with the Development Board to avoid "downloading again again" and wanted to build an NFS env

Build an embedded development environment for S5PV210 Development Board in Ubuntu The development board used in this tutorial is the GEC210 Development Board, core board resource Overview: CPU: S5PV210, SDRAM: 512 MB, Flash: 8 MB, NandFlash: 256 MB. The environment set up in this tutorial can be used for uboot porting

A 51 Development Board was developed recently, as shown in. This board is very simple,All I/O ports are extracted, and Peripherals can be expanded by themselves. P0 is used to pull up the resistance,11.0592 M crystal oscillator, reset key, DC power plug, DC power self-locking switch, microcontroller lock seat, expansion of three VCC And Gnd. Compared with the large development

This time we will introduce a classic problem in the counting combo: dimer lattice model. The question is: How many different dominoes are there for a 64-square chess board? Here, the covering refers to covering the entire board without repetition or omission. It is a possible method of overwriting (the picture is from Wikipedia ): The answer to this question is 12988816. A very large number is defini

This article describes how to implement the website message board function in php, which is based on the changyan message board and Netease post style. For more information, see This article describes how to implement the website message board function in php, which is based on the changyan message board and Netease po

I. Causes and principlesCause: In the past computer burning write bootloader to NAND is using JTAG and Jflash,jtag is connected with the port, the current computer is generally not the same mouth, now generally used cheaper to start the J-link, using USB, you can no longer use the previous Jflash burned write. It is therefore necessary to find a way to J-link write NAND. The following instructions j-link the principle of burning nand. With the realarm2410 Development

the command " vi arch/arm/mach-exynos/mach-itop4412.c" to open the mach-itop4412.c, As shown in the following:then find the " struct platform_device s3c_device_buzzer_ctl " line, as shown in:Change the " #ifdef config_buzzer_ctl"in front of this line to "#if defined (config_buzzer_ctl) | |Defined (config_buzzer_ctl_module) "as shown in:then find the " s3c_device_buzzer_ctl" line, as shown in:Change the " #ifdef config_buzzer_ctl"in front of this line to "#if defined (config_buzzer_ctl) | |D

Chapter 5 setting up the test environment for the s3c6410 Development Board 1, install the Serial debugging tool:minicom① detecting whether the current system supports USB to serial portIsmod | grep usbserial② installation minicomApt-get Install minicom③ Configuration minicomMinicom-s④ Test minicomMinicom2. Burn and Write android systemways to erase nandflash using ebootStep 1 preparatory workConnect the Development

The 5th chapter: Build the test environment of s3c6410 Development BoardThis chapter mainly introduces the Android system installed on the OK6410 Development Board developed on the basis of Samsung's launch of the s3c6410 Development Board.Install serial debugging tool: Minicom1th Step: Detect whether the current system supports USB to serial port2nd Step: Install Minicom3rd Step: Configure Minicom4th Step: Test minicomThe method of erasing Nandflash

First, install the Serial debugging tool: MinicomThe Development Board has a serial port. Can be connected to the PC via serial cable. The Linux driver sends debug information to the PC via a serial cable while outputting debugging information, so the Linux driver can view debug information directly on the PC.Note: Since many new PCs and laptops do not have a serial port, it is recommended that readers buy root USB to serial cable (be sure to buy good

problem Description:Stm32 provides a number of IC entry-level development boards, the price is quite cheap. Stm32f0308-discovery is an entry-level Development Board for the CORTEX-M0 architecture. The following is a brief introduction to it.io Convenient:? As long as a USB cable is connected to the PC for development, theIO from the stm32f0308 IC is drawn from the Development Board to facilitate the use of

Note:ArticleContent Source: ComputerAlgorithmDesign and AnalysisDemoProgramIt is done by myself. Please advise me more! In a checkerboard composed of 2 ^ K * 2 ^ K squares, if there is a square different from other squares, it is called a special square and changed to a special checkerboard. Obviously, there are 4 ^ K positions in the special square on the board. Therefore, for any k> = 0, there are 4 ^ k different special chessboard. The special ch