atheros wifi card

) // driver_ar6000.c -------------------- Enter the driver layer through ioctl at the application layer --------------------------------------------------------------- À if (ioctl (drv-> ioctl_sock, SIOCSIWCOMMIT, iwr) À ar6000 _ ioctl_siwcommit (struct net_device * dev, // wireless_ext.c À ar6000 _ ap_mode_profile_commit (arPriv); // ar6000_dr.c À wmi _ ap_profile_commit (arPriv-> arWmi, p); // wmi. c À status = wmi_pai_send (wmip, osbuf, WMI_AP_CONFIG_COMMIT_CMDID, NO_SYNC_WMIFLAG); // wmi.

The channel set of the Atheros chip wireless network card is generally set to the United States. It is not possible to scan a signal from a 12 or 13 channel. The solution has the following two, decide with one of them by yourself. 1. Install a driver that has been modified by an expert The download address is as follows: http://forums.laptopvideo2go.com/topic/15297-latest-

Analysis on the wifi driver of atheros Ar6003 driver document summary VcD4KPHA + IDxpbWcgc3JjPQ = "http://www.2cto.com/uploadfile/Collfiles/20140831/2014083109355817.png" alt = "\"> 1. wmi: wireless module interface // wireless module structure 2. bmi: bootloader message interface 3. htc: host target communications 4. wps: wifi protected setup 5. CS: con

have abandoned this method. This problem does have a driver problem, first, download a CommView for WiFi software. The version and model are of course the latest, so I will not write the model, as for the purpose of the software, you can search for it on the Internet. It is also a method for cracking wifi in Windows. After installing the software, right-click my computer and choose "manage"> "Device Manage

After the installation of CentOS 5.5 system, some people appear to be unable to surf the internet phenomenon, detected by the detection is Atheros AR8151 network card can not recognize, encounter this problem do not be afraid, the following small series to give you the next CentOS 5.5 unrecognized Atheros network card

I do the network card driver, the main content is to design and improve the rate adjustment algorithm, With the new standard of 802.11 protocol cluster more and more, the rate is more and more high, modulation coding method is also more and more, generally speaking, the higher the rate is more likely to drop packets, the lower the rate is more stable, this is the overall situation, but not necessarily the law, so, only with a fixed rate to send is obv

Different countries and regions have different radio management regulations (Regulatory Domain), and there are also different rules for the division of the ISM 5 GHz band.Regulatory Domian has three major families: the FCC represented by the United States, ETSI represented by the European Union, and TELEC, once again a maverick in Japan (both in the cellular network and WLAN, japan has always been a weird existence ). China adopts ETSI regulations. The specific frequency band management is diffe

Recently I installed the Ubuntu 11.04, the system runs stably, the interface Yong Rong, more than the death of the dead do not know how many times, but found that wireless network card can not be connected to the Internet, find wireless routers, in the home when the Internet is inconvenient, for one months, did not find a good plan. Recently finally found a solution to this: The solution to the problem is to install the Madwifi

Install the official small WiFi drive, only let it as a wireless signal transmitter, but I want to through the small WiFi to allow my desktop computer can all receive wireless signal, so after a toss finally success. Mine is Win7.Small WiFi does not accept the wireless signal, can not be used as a normal wireless card.

I don't think WiFi is important at home, and I can't afford to go out without a lot of traffic. Now let's see how the WiFi Butler can get the WiFi card, even if there is no wifi, to the WiFi c