REDHAT7 Setting up NTP (Time synchronization)Installation:# yum Install NTPStart:# Systemctl Start ntpd# Systemctl Enable NTPDTo view synchronization:# ntpq-pOpen firewall:# Firewall-cmd--permanent--ADD-SERVICE=NTPNTP server is now completeClient synchronizes from NTP serverInstallation:# yum Install NTPTo modify the c
NTP server1. Enter Rpm-qa|grep NTP to see if an NTP server is installed2. If the Yum-y install NTP installation is not installed3. Modify/etc/ntp.conf Add the original server annotated local s
An error is displayed when you use RHEL as an NTP server to update ntpdate on the server. My configuration is as follows: restrict127.0.0.1restrict-6: 1restrict10. Conflict
An NTP server is built using RHEL. An error is displayed when ntpdate is updated on the
Centos uses ntp to maintain time synchronization 01www.2cto.com # Install and start ntp02yuminstallntp03chkconfigntpdon04ntpdatepool. ntp. org05servicentpdstart0607 # Modify the time zone www.2cto. com08ln-s/usr/share /... centos uses ntp to maintain
installing the NTP serviceYum-y Install NTP ntpdateTo modify a configuration file:Make a backup first:Cp/etc/ntp.conf/etc/ntp.conf.bakThen modify:Vi/etc/ntp.confWhat this file needs to be modified:Find the following two lines, this default is only allow native query, you can add these two lines # comment outRestrict 127.0.0.1Restrict-6:: 1Then add the following so that the meaning is to allow 1.0 network s
Windows is used for several years, and there is always a time to change the system time. However, it is easy to adjust the system time. It is not that easy to call up a correct one. A few years ago (when I was still in college, it was about a junior) I used C # To write an NTP
Program But when the
NTP time conversion, Baidu has long been no results. I have tried it for myself.
The time the packet is sent on the device is NTP format, and the raw data in the Wireshark is:
DA E5 D0 E5
1, through the struct.unpack, into the integral type:
S4=struct.unpack (' 4 B ', buf[0][102:106])
The results are as follows: 218 2
First step to install NTPYum Install NTPSecond step, find the closest time synchronization serverHttp://www.pool.ntp.org/zone/asiaThe third edition of/etc/ntp.confServer 127.127.1.0 iburst # Local Clock when the external time server is unavailable, use the native time as the standard for the
.
Regardless of the time that we want to sync the system through any channel, the provider will usually give only the utc+0 time value and not the time zone (because it doesn't know where you are). So when we set the system time, it's the first thing to do
# date
Thu Oct 11:22:45 EDT 2013
If the
1. change the system time zone to the Shanghai time zone cp/usr/share/zoneinfo/Asia/Shanghai/etc/localtime2. write a script ntp. cron #! /Bin/bash/usr/sbin/ntpdatentp.fudan.edu.cn | logger-tNTP put the script in/etc/cron. daily...
1. change the system time zone to the Shanghai tim
The local clock in the Xen Linux machine is by default (done) synchronized with the physical host clock, in order to change the time it uses the Sync Service for NTP, the kernel parameters must be set by the virtual machine:Shell CodeEcho 1 >/proc/sys/xen/independent_wallclock
The/etc/sysctl.conf configuration file in the virtual machine adds the following two and takes effect after reboot.Config code# Set
1. Select a server as the time synchronization server.2. Run regedit to open Registry Editor.3. Locate the registry key hkey_local_machine\system\currentcontrolset\services\w32time\config\, and in the right window, change the value of AnnounceFlags to 5.4. Continue to locate the registry key Hkey_local_machine\system\currentcontrolset\services\w32time\timeprovide
Server-side:1. PackagingSlightly....2. Modify the NTP service configuration fileConfiguration file location:/etc/ntp.confWhat to modify:# Set the IP network segment to synchronize with the server time , the following is the 192.168.x.x machine can synchronize with the serverRestrict 192.168.0.0 mask 255.255.0.0# Set th
NTP server: Network time Protocol (NTP) is a protocol used to synchronize the timing of a computer, which allows the computer to synchronize its servers or clock sources (such as quartz clocks, GPS, etc.) It provides high-precision time correction (less than 1 milliseconds o
Basic configuration fileYou want to configure local time server server 127.127.1.0 must write this# --- GENERAL CONFIGURATION ---server aaa.bbb.ccc.dddserver 127.127.1.0fudge 127.127.1.010# Drift file.driftfile /etc/ntp/driftMy exampleRestrict 192.168.0.0 mask 255.255.25
Automatically synchronize the date and time of a linux host through network ntp
If you only need to synchronize data once, run the following command:
Rdate-s time.nist.gov
WhereTime.nist.govIs a time server, of course, you can also use another time
GMT/UTC/CST;/etc/localtime,/usr/share/zoneinfo/* time zone file,/etc/profile plus TZ variable;Hardware time RTC, system time; date,hwclock,tzselect;/usr/share/zoneinfo/asiaZdump Sichuan View the current time for each zone# Hwclock--set--date= "Mm/dd/yy hh:mm:ss" Set hardware time
NTP Server Setup1. determine that two hosts are in the same network segment and can ping each other 2. Click start , click run , type regedit, and then click " Determine " . 3. Locate and click the following registry subkey:Hkey_local_machine\system\currentcontrolset\services\w32time\parameters\type4. in the right pane, right-click the Type, and then click Modify . 5. " edit value " " numeric dat
If you only need to synchronize once, then execute the following command to rdate-stime.nist.gov where time.nist.gov is a time server, of course you can also use another time server. If the time of multiple servers needs to be fully synchronized, it is best to configure a un
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.