bgp route reflector

BGPIs the routing protocol used to connect to an independent system on the Internet. It is an enhanced, comprehensive, and scalable protocol developed by the Internet Engineering Task Group. BGP4 supports the CIDR addressing scheme, which increases the number of available IP addresses on the Internet. BGP was designed to replace the original external gateway protocol EGP and is also considered a path vector protocol. The

exists in a route, the RR will not create a new originator_id. (2) When other BGP speaker receive this route, they will compare the received originator_id and the local Router ID, if two IDs are the same, BGP speaker ignores this route and does not process it. The Origin

34.1.1.3 255.255.255.0Duplex AutoSpeed auto!Interface FASTETHERNET0/1IP address 23.1.1.3 255.255.255.0Duplex AutoSpeed auto!router OSPF 100Router-id 3.3.3.3Log-adjacency-changesNetwork 3.3.3.3 0.0.0.0 Area 0Network 23.1.1.0 0.0.0.255 Area 0Network 34.1.1.0 0.0.0.255 Area 0!Router BGP 200No synchronizationBGP Router-id 3.3.3.3BGP log-neighbor-changesNeighbor 2.2.2.2 Remote-as 200Neighbor 2.2.2.2 Update-source Loopback0Neighbor 2.2.2.2

Why?BGPCannot be aggregated with itRoutingWhich of the following network segments does the device establish a neighbor? A: If BGP establishes a neighbor with the device of the network segment to which the aggregation route belongs, when the device or link of the target network segment fails, it cannot be sensed through the aggregation route, the device will still

Basic Configuration: R1: Router bgp 9806 Nei too many connections 20 remote-as 4808 Bgp router-id 1.1.1.1 R2: Router bgp 4808 Nei 1.1.1.1 remote-as 9806 Nei 1.1.1.1 update-source lo0 Bgp router-id 255.255.255.255.20 Network bandwidth limit 21 mask limit 255 Only the bgp neig

BGP is a familiar protocol. Then, let's give a brief explanation of this Protocol. It mainly targets its synchronization performance. You need to pay attention to this aspect. BGP protocol: A router running the BGP protocol will not advertise the routing information learned from the internal peer (IBGP neighbor) to the external peer (EBGP neighbor ), unless the

At present, there are also a lot of BGP routing protocol applications, so I have studied the synchronization problem in the BGP routing protocol. Here I will share it with you and hope it will be useful to you. BGP protocol: A router running the BGP protocol will not advertise the routing information learned from the i

routes are routed to the two core routers, only the optimal route is reflected, that is, the route with *>, therefore, only one route entry is displayed on the two core routers. 3. For the next-hop-self command, when using some commands on the two route reflectors, the next hop will not be changed to itself when the r

Technorati labels: BGP, CCIE, default-information, originate, route BGP default-information originate function testing report 1, Requirement description This Testing need check MAIPU and cisco bgp default-information orginate compatible with each other or not. 2, Testing topology 650) this. width = 650; "style =" backg

Bgp dampeningTo enable BGP route dampening or change various BGP route dampening factors, use the bgp dampening command in address family or router configuration mode. to disable the function or restore the default values, use the

Key Issues 1) How does an ACL match route entries with the same subnet and different masks? How do I match entries with the same mask and different subnets? 2) Why does a summary route cause a tumble of BGP peers? 3) Why does the acl fail to match the route entry when attribite-map is used? 4) How to Use advertise-map,

important attribute inherent in BGP. In ASPATH and BGP Route update, the passed self-developed domain (AS) number is added to the update. In this way, when BGP finds that its own AS is also in it, it can be considered that a loop has occurred. EBGP can consider this AS no problem. In some scenarios, there will be prob

In the IGP era, we all know, for example, OSPF, link state protocol, in the routing of the time, than the cost of the link, which link consumption will be more priority, if two of the same link consumption, then do load balancing. In fact, the 2 principles to achieve the OSPF---shortest path first work principle. What if, in BGP, there are multiple routes to achieve the goal, how should the choice be made? Which path is the preferred one? Take a lo

BGP Route update timer analysis defines the BGP Route update timer on RFC4271 of BGP. This timer can only work for routes with the same prefix of the same address family, its main function is to prevent a route in the network from

Local-preferenceLocal Priority PropertyOnly exchanged between IBGP peers and not advertised to other asThe greater the priority, the higher the priority, the default is 100For multiple exits of the same as, go out of the waybelongs to any recognized attributeNote: The source route delivery direction + specified peer+ the direction (Import/export) that you want to pass in order to correctly apply the routing policy.650) this.width=650; "Src=" Http://s1

Principles and configurations of the BGP protocol for HCNP learning notes 3-route AggregationThe BGP protocol can use commands to aggregate specific routes into an aggregation route. The Routing aggregation principle adopts the longest matching method with the same mask. Route